Ask the Car People.SM


Please Help!!!

15 messages,  Last post on May 09, 2012 at 10:15 AM

You are in the Nissan Quest Forum.

What is this discussion about? Mercury Villager, Van

Messages Page 2 of 2

#7 of 15 Please help! Misfiring uphill by cheri6

May 08, 2009 (8:11 pm)

I spent some time reading old posts about this problem as mine is doing the exact same thing. Misfiring, bogging out/surging when going up hill and missing-loosing power moreso when van gets warmer. In reading old posts it seems that the most common problem is the dirty photo whatever under the distributor and most clean that off or change the distributor and that seems to be the remedy to this problem. Mostly from what I have read here in all the old posts. I had the fuel filter changed and that didn't do it. So my next will be the above mentioned.

#8 of 15 Re: Please help! Misfiring uphill [cheri6] by jedft

May 09, 2009 (10:17 am)

Replying to: cheri6 (May 08, 2009 8:11 pm)
So I got around to it today and pulled my distributor off and apart. My problem was NOT the camshaft position sensor, but the distributor shaft bearing was throwing shrapnel all around inside there causing erratic readings on the CPS. After the engine would heat up the shaft would start wiggling around due to lack of 3 or 4 balls in the bearing. That threw the timing off so bad the engine would stall. So... I replaced the distributor and problem solved. Oh, and that "un-replaceable" camshaft position sensor. I have a spare now. It comes off with 2 screws. What a racket the parts business is.

#9 of 15 Re: Please help! Misfiring uphill [jedft] by mrb915

Jun 13, 2009 (6:15 pm)

Replying to: jedft (May 09, 2009 10:17 am)
Thanks for the posts here. My 1999 Villager was running so poorly and I had replaced distributor cap, spark plugs, wires, and fuel filter to no avail. Finally, as a result of this forum, I forked out the 300 bucks and BINGO, fixed. Thanks a bunch everyone!

#10 of 15 Re: Please Help!!! [tank180] by snorkelbobby

Jun 21, 2009 (10:27 pm)

Replying to: tank180 (Apr 09, 2009 5:33 pm)
I believe you have a bad distributor. The bearing goes bad and produces brown dust whcih coats the camshaft optical sensor in the distributor. To confirm, remove the cap and rotor (1 screw) and the slotted plate. Look for brownn dust. Clean optical sensor. It will work for a short while. Get reman distributor on ebay for $200 or less.
 
go here for more help, files & photos
 
http://autos.groups.yahoo.com/group/villagerquest/

#11 of 15 2000 Villager front Cat problem by traveler359

Jul 09, 2009 (12:14 pm)

I have a 2000 villager, that needs the front Catalytic Converter replaced. The type thats on it is one that has the manifold as part of the cat. I've looked all over online, so has the muffler shop and no one can find it. All that were finding it a front cat with a connecting pipe that ends with two holes for exhaust flow. Not the manifold cat. I don't know why there are 2 different parts like this. But has anyone else experienced this, is there a manifold part that I can add, so as to be able to use the after market parts that I am finding?
 
TIA
trav

#12 of 15 Re: Please help! Misfiring uphill [mrb915] by jessie19

Jul 15, 2010 (9:20 am)

Replying to: mrb915 (Jun 13, 2009 6:15 pm)
I know this is an older post but perhaps someone now can benefit from this information.
 
I have a 2000 villager that experienced the same issues as mentioned above, after it warmed up it would miss and buck. After a trip to the shop for a diagnostic and a quote of 500 bucks I replaced my self the Cap, wires, rotor, and plugs...no luck! I took it to a Ford dealership and they replaced the air filter telling me that it was a Mass airflow sensor, however they were unable to pull diagnostic codes because it has a Nissan Engine.
 
I tore the distributer apart and the Upper distributor shaft ball bearing was missing the ball shield and 4 balls, I suspect they are sitting on top of the Lower ball bearing that is still intact. Not causing any harm....
 
For 21 dollars I bought a new Bearing 10mm ID, 26 mm OD, 8mm thick, and installed it without ever removing the distributor...a little tricky but it worked great. Sure beats forking out several hundred for a new or rebuilt distributor.
 
Good Luck!

#13 of 15 Mercury Villager and Nissan Quest by rq777

Aug 26, 2011 (8:03 am)

Are the parts for the Mercury villager 2000 v6 3.3L interchangeable with the Nissan Quest? Like the catylictic convertor?

#14 of 15 Re: Mercury Villager and Nissan Quest [rq777] by steve_ HOST

Aug 27, 2011 (5:12 pm)

Replying to: rq777 (Aug 26, 2011 8:03 am)
Should be - they are twins and just some of the trim and cosmetic bits should be different.
 
Try searching for parts at RockAuto.com and see if the part numbers are any different.
 
Steve, visiting host

#15 of 15 Re: Mercury Villager and Nissan Quest [rq777] by bkpie

May 09, 2012 (10:15 am)

Replying to: rq777 (Aug 26, 2011 8:03 am)
Yes they are the same. They are pricey but Davico has the least expensive and they are made as exact fit items

Messages Page 2 of 2

To POST a message, please Sign In.

Advertisement

Browse by Category

Browse by Vehicle
   View All Vehicles

Browse by Board
Browse by Topic
View All Topics

Edmunds Community

Advertisement