Last post on Apr 17, 2012 at 7:24 AM
You are in the Buick Lucerne
What is this discussion about?
Buick Lucerne, Lighting, Sedan
#1 of 11 How to change a headlamp in a Lucerne
Mar 27, 2009 (7:04 am)
I have a dead lamp in my 06 Lucerne, and thinking it was easy to replace like my 00 LeSabre, I removed the three bolts hoping the whole unit would come out and I could replace the dead bulb.
Not so..it was loose, but will not come out. There is no way to change any bulbs without the whole head light assembly pulled out.
I read on another site, that you have to take the whole plastic bumper off, in order to remove the headlight assembly. Does anyone know if this is true?
Anyone had experience with this? Thanks. Bill
#2 of 11 headlamp removal
Mar 05, 2010 (9:03 am)
Yes, you have to take the front bumper cover off, also you have to take some screws out of the inner fender well to get to the bolt on the very end of the headlamp assembly.
#3 of 11 Re: headlamp removal [bill5983]
Apr 08, 2010 (5:08 am)
I can't imagine it being that difficult to change a headlamp bulb. You have to go to a bodyshop to do this now if you are not mechanically inclined. They should not be designed this way. Rediculous!
#4 of 11 Re: headlamp removal [bill5983]
Apr 13, 2010 (6:01 am)
My Buick dealer quoted me a price of $136.00 to change my headlamp bulbs. I really would like the brighter lights to help me see better in early a.m. when I leave for work. But that seems expensive to change a headlamp and that does not include the price of the bulbs. I did notice a round unscrewable panel in the front fender wells just barely big enough to get my hand in once it is removed. Does anyone know what this is for?
#5 of 11 Re: headlamp removal [nace818]
May 12, 2010 (2:33 pm)
Answering my own post, but I decided to go with a full HID conversion since the bumper cover had to come off anyway. It's beautiful. If anyone has night blindness like I do this is the answer, Much better at night and they look really good aglow.
#6 of 11 Buick Lucerne 2006 headlamp replacement
Aug 03, 2010 (7:26 pm)
To replace the drivers side headlamp you do not need to remove the bumper as the dealer instructions call for. Take off the front shield that goes across the front of the engine. On the drivers side take of the air box and filter cover-there should be 3 metal clips on the lower motor side of the box. When open, slide out the engine electronics module and put it on top of the engine. There is plenty of slack to move it safely out of the way. Remove the lower part of the filter box using 3 torx screws-mine were tight. When these parts are removed you can access the back of the headlamp assembly. I followed the dealers recommendation and removed the tire, wheel well liner, 3 screws on the assembly and had a very difficult and lenghty time getting the work done. The way I first mentioned works well and you should be able to get the bulb replaced in under an hour. Also 2 additional things, you need to remove the flexible rubber air hose from the engne to the intake and also a connector on the side of the air box. It is not easy to forget to recconect the large air tube, but the sensor connector on the side ma be easy to forget.
#7 of 11 Re: Buick Lucerne 2006 headlamp replacement [jp001]
Aug 04, 2010 (2:45 pm)
IMO, it is just not right for it to be so difficult to change a bulb. Bad engineering on a fine car.
#8 of 11 Re: Buick Lucerne 2006 headlamp replacement [jp001]
Sep 02, 2010 (7:58 am)
Does anyone know about the fog lamps? Is it the same difficult procedure of removing the bumper cover first to change one?
#10 of 11 Re: headlamp removal [nace818]
Apr 12, 2012 (12:05 pm)
Hey nace818 -
I have been thinking of making the HID conversion on my 2006 CXS but I have some reservations about doing it. My fears are:
1. Getting a cheap/low quality HID kit. Which one do you have?
2. Where to locate the ballasts. Seems like it would look bad, rattle, Etc.
3. Flickering lights... Do you have any issues? Did you need any resistors?
Please let me know how your HID conversion went. Thanks.