You are here: Forums SUVs GMC Yukon Rear Defroster Dilemma

Rear Defroster Dilemma

4 messages,  Last post on Mar 16, 2009 at 2:41 PM

You are in the GMC Yukon Forum. Your Hosts are steve_ & tidester

What is this discussion about? GMC Yukon, GMC Yukon Denali, GMC Yukon XL, Auto Repair, Truck

Messages Page 2 of 2 1 2 Prev Next Last

Go To Msg # Search This Discussion

#2 of 4 Re: Rear Defroster Dilemma [10mikeymike] by rsht Mar 16, 2009 (6:46 am)
Replying to: 10mikeymike (Mar 15, 2009 5:14 am) After reading your post, I had a close look at my 07 Denali, which I open/close the glass portion much more frequently than I do with the entire tailgate (just the opposite of what you do). So far, I have not had any problem with the terminals/connectors on mine (knock on the wood...). I do agree, those coiled wires, although coiled designed to stretch , they do still seem tight with quite a bit of tension on the terminals... Anyhow, when I looked at the heating element terminals, each seems to be constructed with two piece parts (the base, and the male terminal - which is soldered on to the base), the base is where attached (via some kind of PINK colored adhesive) on to the heating element on each side. Its my opinion: Try to adjust the angle of the male terminal (where its soldered on to the base) to be a bit more steeper to the glass (make it closer to the glass - lesser degree from the base to the terminal), so there is less "bending" force on where its soldered to the base...   There are different types of solders (some with more/less lead content) as far as being able to handle the temp changes and the rate of current flow; but, I would assume the dealership would know the exact solder to use.... Besides, you had the entire rear glass with element and terminals replaced, so the type of solder used are all OEM so should not be the issue here. Good Luck! Replies to this message: 10mikeymike (Mar 16, 2009 12:52 pm) rsht (Mar 16, 2009 2:41 pm)
#3 of 4 Re: Rear Defroster Dilemma [rsht] by 10mikeymike Mar 16, 2009 (12:52 pm)
Replying to: rsht (Mar 16, 2009 6:46 am) Thanks for the response. Thanks also for checking yours out. After posting my thread yesterday, I decided to go out and super glue mine back on. I figure Winter's almost over and if necessary, I'll deal with it again next Winter. In the meanwhile, I didn't want to see the wire and connector dangling every time I look in the rear view mirror. After gluing the terminal back on and letting it cure, I reattached the wires. Within a few minutes I touched the base of the terminals on either side of the window. I was amazed at how hot each of them were. I realize they have to generate some heat to accomplish their intended purpose, but I'm now convinced that they may be getting too hot and melting the solder as a result. While I can't confirm it, I also believe that the rear defroster may come on when I remotely start the vehicle. If that's the case, it will probably melt the super glue and/or the solder on the other side very soon and confirm my suspicions. Either way, now I will tell the dealer to look beyond the terminals for the root cause of the problem. Replies to this message: rsht (Mar 16, 2009 2:41 pm)
#4 of 4 Re: Rear Defroster Dilemma [10mikeymike] by rsht Mar 16, 2009 (2:41 pm)
Replying to: 10mikeymike (Mar 16, 2009 12:52 pm) NP. Wow! Hot enough to melt the solder? Ouch! Something doesn't sound quite right...   Earlier I had a chance to try out my rear defrost and below are my observations: 1. My rear defrost does not come on automatically when I remote start my Denali, unless I leave it on when I turn-off my vehicle. Even when leave the the rear defrost ON, as I recall, it will turn itself off automatically after approximately 15 minutes or so (did not clock that)... 2. I ran my rear defrost for about 9 minutes or so, then I opened the rear glass and touched each terminals with my index finger, they were no where close to "hot". Each was only warm to touch and I was able keep my finger on the terminal with no problem... I believe you are right to tell your dealer to look beyond the terminals, they need to make sure there is not a short circuit somewhere before attempting to solder the terminals back on again... Good Luck to you!!

Messages Page 2 of 2 1 2 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums SUVs GMC Yukon Rear Defroster Dilemma