You are here: Forums SUVs Ford Expedition Ford Expedition not blowing heat and clicking noise

Ford Expedition not blowing heat and clicking noise

14 messages,  Last post on Dec 04, 2009 at 7:31 AM

You are in the Ford Expedition Forum. Your Hosts are steve_ & tidester

What is this discussion about? Ford Expedition, Heating / Cooling, SUV

Messages Page 2 of 3 1 2 3 Prev Next Last

Go To Msg # Search This Discussion

#3 of 14 Blend Door Actuator by alwaysfords2 Jan 26, 2009 (8:51 am)
There are two blend doors for the rear air / heat, both of which are on the passenger side under the rear quarter window. it is typically the actuator that breaks on these as opposed to the blend door axle that breaks in the front requiring the removal of the dash. One is very simple to get, the other is a little tougher. To see if you have the simple one remove the "change tray" under the p/s quarter window. there is a small being box right on top of the wheel well. Unclip the electrical connector. If the noise stops, that is the broken one and it is a 3 bolts to remove and replace. Replies to this message: jlopez3 (Feb 25, 2009 7:53 am)
#4 of 14 Re: Blend Door Actuator [alwaysfords2] by jlopez3 Feb 25, 2009 (7:53 am)
Replying to: alwaysfords2 (Jan 26, 2009 8:51 am) hello, where is the second actuator "tougher one" located? do you know the price for each?
#5 of 14 by alwaysfords2 Feb 25, 2009 (8:51 am)
It is within that same trim panel, but it is further forward and slightly around the front of the wheel well. Some people have posted that they have been able to make the replacement without taking off the trim panel. If you have to take the panel off it is a big job - you have to start at the back hatch and take off the threshold and move forward from there. You will also need to remove the seat belt attachment at the second row I think. The part itself is cheap - I got mine for $25 including shipping. They are different part numbers, so you need to make sure you get the correct one. Replies to this message: nerdy1 (Nov 27, 2009 12:53 pm) alwaysfords2 (Nov 28, 2009 4:01 am) nerdy1 (Nov 28, 2009 6:00 am) and 2 more...
#7 of 14 1998 ford expedition by fckford Nov 17, 2009 (10:08 am)
where is the frnt heating and air climate control located and what is there to change out? The back works fine.
#8 of 14 Re: [alwaysfords2] by nerdy1 Nov 27, 2009 (12:53 pm)
Replying to: alwaysfords2 (Feb 25, 2009 8:51 am) Can you tell me where to get the part? Ford wants 500.00 for one. Replies to this message: alwaysfords2 (Nov 28, 2009 4:01 am) nerdy1 (Nov 28, 2009 6:00 am) alwaysfords2 (Nov 28, 2009 2:19 pm) and 1 more...
#9 of 14 Re: [nerdy1] by alwaysfords2 Nov 28, 2009 (4:01 am)
Replying to: nerdy1 (Nov 27, 2009 12:53 pm) You must be talking past the guy about different things. The blend door actuators range in price from $25 to $50 depending on where you get them. They must be quoting you some other part. I got mine on line form a Ford delaer for $25. Replies to this message: nerdy1 (Nov 28, 2009 6:00 am) alwaysfords2 (Nov 28, 2009 2:19 pm) nerdy1 (Nov 28, 2009 3:45 pm)
#10 of 14 Re: [alwaysfords2] by nerdy1 Nov 28, 2009 (6:00 am)
Replying to: alwaysfords2 (Nov 28, 2009 4:01 am) i bought a thing that went on top of the housing that looks a little like a tape cassette and i still have the clicking noise deeper down inside the housing. Do you know what this part maybe that is clicking now? Thanks Replies to this message: alwaysfords2 (Nov 28, 2009 2:19 pm) nerdy1 (Nov 28, 2009 3:45 pm)
#11 of 14 Re: [nerdy1] by alwaysfords2 Nov 28, 2009 (2:19 pm)
Replying to: nerdy1 (Nov 28, 2009 6:00 am) There are two of those - one controls floor to ceiling mix, and one controls hot cold mix. The floor to ceiling one is the one on top, the hot cold one is the one that is down lower. Same size part, often times it is a differnet part number for the second one becuase the axles are slightly different. It is lower and forward of the first. I have read that some people have done it with the trim in place through the change tray and cup holders, others have opted to take all the trim off from the hatch opening forward. Replies to this message: nerdy1 (Nov 28, 2009 3:45 pm)
#12 of 14 Re: [alwaysfords2] by nerdy1 Nov 28, 2009 (3:45 pm)
Replying to: alwaysfords2 (Nov 28, 2009 2:19 pm) I wanted to give you a big THANKS. It was the 2nd one down lower. Replaced the top and still had noise. Pulled off cover to see the 2nd one and when my son unplugged it the noise stopped. You are also right about a different axle on both of them. So my total was 46.35 to fix and not the 501.00 plus labor at Ford. I really can't say THANKS enough. You are wonderful. Nedra

Messages Page 2 of 3 1 2 3 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums SUVs Ford Expedition Ford Expedition not blowing heat and clicking noise