You are here: Forums SUVs Ford Expedition Ford Expedition not blowing heat and clicking noise

Ford Expedition not blowing heat and clicking noise

6 messages,  Last post on Feb 25, 2009 at 8:51 AM

You are in the Ford Expedition Forum. Your Hosts are steve_ & tidester

What is this discussion about? Ford Expedition, Heating / Cooling, SUV

Messages Page 1 of 1 All Messages Displayed

Go To Msg # Search This Discussion

#1 of 6 Not blowing heat for awhile and clicking noise by ArmyWife0306 Nov 29, 2008 (5:56 pm)
I have a 2003 Expedition EB and when I go to take the kids in the morning the heat will not blow for at least 25 mins. You can hear it blowing but nothing comes out. Anyone know what might be wrong.   I also have a clicking or thunking noise coming from the back around the 3rd row area. It seems to make different sounds as to what the temp is turned on, on the rear control.   I have an extended warrenty on the car, bumper to bumper, so it should be covered. I would just like to take it in knowing something about it. Thanks! Replies to this message: fordexpo (Jan 24, 2009 4:09 pm)
#2 of 6 Re: Not blowing heat for awhile and clicking noise [ArmyWife0306] by fordexpo Jan 24, 2009 (4:09 pm)
Replying to: ArmyWife0306 (Nov 29, 2008 5:56 pm) I have worked on Fords for many years and I know that many of the ones with electronic climate control have an electric blend door that opens and closes between the heat and cold air to get the temp right. I have seen them jam and click over and over and then sometimes start working. Then again our towncar never starting working again and only clicked and it was cold. I purchased the blend actuator motor at Lincolm Mercury (FORD) for $38.00 of so and removed the dash to install in a few hours at our home. Lincoln Mercury wanted $700.00 something to fix. Worked fine after the repair and a few beers.
#3 of 6 Blend Door Actuator by alwaysfords2 Jan 26, 2009 (8:51 am)
There are two blend doors for the rear air / heat, both of which are on the passenger side under the rear quarter window. it is typically the actuator that breaks on these as opposed to the blend door axle that breaks in the front requiring the removal of the dash. One is very simple to get, the other is a little tougher. To see if you have the simple one remove the "change tray" under the p/s quarter window. there is a small being box right on top of the wheel well. Unclip the electrical connector. If the noise stops, that is the broken one and it is a 3 bolts to remove and replace. Replies to this message: jlopez3 (Feb 25, 2009 7:53 am)
#4 of 6 Re: Blend Door Actuator [alwaysfords2] by jlopez3 Feb 25, 2009 (7:53 am)
Replying to: alwaysfords2 (Jan 26, 2009 8:51 am) hello, where is the second actuator "tougher one" located? do you know the price for each?
#5 of 6 by alwaysfords2 Feb 25, 2009 (8:51 am)
It is within that same trim panel, but it is further forward and slightly around the front of the wheel well. Some people have posted that they have been able to make the replacement without taking off the trim panel. If you have to take the panel off it is a big job - you have to start at the back hatch and take off the threshold and move forward from there. You will also need to remove the seat belt attachment at the second row I think. The part itself is cheap - I got mine for $25 including shipping. They are different part numbers, so you need to make sure you get the correct one.

Messages Page 1 of 1 All Messages Displayed

Go To Msg # Search This Discussion

You are here: Forums SUVs Ford Expedition Ford Expedition not blowing heat and clicking noise