You are here: Forums Coupes & Convertibles Chrysler Sebring Chrysler Sebring Engine Problems

Chrysler Sebring Engine Problems

42 messages,  Last post on Dec 01, 2009 at 6:26 PM

You are in the Chrysler Sebring Forum. Your Host is claires

What is this discussion about? Chrysler Sebring, Engine, Sedan

Messages Page 3 of 5 1 2 3 4 5 Prev Next Last

Go To Msg # Search This Discussion

#20 of 42 1999 chrysler sebring i have no fire through dist. by mike334 Feb 09, 2009 (1:07 pm)
i have a 1999 chrysler sebring 2.5 v6 it was running fine i parked it and it hasnt fired since i have replaced distributor and crank sensor still has no fire through dist . has anyone had this problem and what else can i do it turns over like a champ but will not fire Replies to this message: liverboy58 (Jul 26, 2009 2:08 pm)
#21 of 42 1999 chrysler sebring by peodigy Feb 09, 2009 (2:29 pm)
Haven't had that one. But it would be interesting to see what Chrysler has to say. So far my 2007 still has engine light on and they say nothing shows up on diagnostic still! No shut offs while driving for about 3 wks.
#22 of 42 Re: 2.4 woes [41coupe4me] by esw52892 Feb 26, 2009 (5:04 pm)
Replying to: 41coupe4me (Oct 04, 2008 2:24 pm) Those engines are mitsubishi manufactured
#23 of 42 engine noise by malopr Jul 03, 2009 (4:38 pm)
97 sebring v6 2.5. consistent ticking and/or tapping noise in the engine, it does not stall or turn off. runs good except for the noise coming frim the engine. also the tach is not working, console battery light stay on when engine is on does not run off Replies to this message: derek61 (Jul 26, 2009 8:58 pm)
#24 of 42 Re: 1999 chrysler sebring i have no fire through dist. [mike334] by liverboy58 Jul 26, 2009 (2:08 pm)
Replying to: mike334 (Feb 09, 2009 1:07 pm) I had that problem with my 98. It took forever to figure it out. It was the antitheft relay. On the 98 it has three relays on the firewall, it is the middle one. All I can say is try that. It's pretty cheap too. It worked for me.
#25 of 42 2001 sebring missing by derek61 Jul 26, 2009 (8:58 pm)
Replying to: malopr (Jul 03, 2009 4:38 pm) my sebring is not firing on # 4 cylinder , it has the 2.7 liter with indivudual coils for each plug , i swapped the coils around and no help , i pulled the coil off the plug and stuck a new plug in the end of the coil and ran the engine and stuck the spark plug close to metal ... no spark , anyone have any idea , maybe the ecm? thanks
#26 of 42 2006 Chrysler Sebring Touring convertible 2.7L by penb Aug 21, 2009 (12:54 pm)
Our car had 52,000 miles on it and we started to loose compression. We took itto Chrysler and they told us a valve spring broke and the valve stem bent. They were replaced for cylinder #4. That was July 1, 2009. We got our car back after a slow return to us on July 10th drove it and on July 18th we broke down. Car would not start. Then we got going and engine light came on so we had it towed back to Chrysler and they told us oil pump broke because an impeller blade broke inside the pump. The end result is we need a new engine and we only had 53,000 miles on the car. For the Valve spring Chrysler kicked in $400.of the $1200 job. Now for the $5380 engine they are billing us $2690. Our warranty was only for 36,000 miles but we did not abuse the engine. It wasn't suppose to fail at 53,000. Has anyone had this experience? I really only want to buy American, but now I will have to really pray about my next car. Replies to this message: jpf (Aug 25, 2009 10:34 am)
#27 of 42 2006 Sebring Overheating by cowboy2679 Aug 24, 2009 (10:46 am)
I have a 2006 Sebring with a 2.7 V6. My issue is that the car takes a very long time to warm up, but once it does the thermostat gauge continues a steady climb until the car is overheating. The thermostat has been replaced coolant level is good, and I have no ideas on what steps to take next. If anyone knows what the problem could be thank you in advance.
#28 of 42 Re: 2006 Chrysler Sebring Touring convertible 2.7L [penb] by jpf Aug 25, 2009 (10:34 am)
Replying to: penb (Aug 21, 2009 12:54 pm) The past history of the 2.7 v6 engine is not very good. Four or five years ago these engines had a sludging problem and problems with the timing chain. I'm not so sure if these issues have been resolved. The local Dodge-Chrysler dealer always has lots of Chargers or 300's with this engine on their lot. I think it's because buyers stay away from this engine. If Chrysler is willing to pay half the cost you're probably better off taking them up on it and replace the engine. Try to get at least a 50,000 mile warranty on the engine. Good luck.
#29 of 42 2.7 L New Water Pump Now No Start by thecardoc Sep 02, 2009 (7:40 pm)
After installng new water pump now no start. 2002 sebring 2.7L . The timming chain was absolutly positively right on the marks . And just to make shure I cranked it through about 10 to 12 rotations to get the marks to align again. And they were still right on the money. I get 150 to 180 psi compression on all cyls . Cranks good and fast has spark. No codes show up on my OTC genisys. Did try replacing the cam sensor with no results. Any help or coments welcome. Replies to this message: thecardoc (Sep 05, 2009 7:18 pm) chellno1 (Oct 13, 2009 7:40 pm) thecardoc (Oct 14, 2009 3:30 pm)

Messages Page 3 of 5 1 2 3 4 5 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Coupes & Convertibles Chrysler Sebring Chrysler Sebring Engine Problems