2004 Dodge Stratus Camshaft Position

disconnecting the battery should have turned the light off . before buying a EGR vaulve disconnect the vaccum line and plug it off. if the car runs better just leave it disconected.u dont need it any way.its just for polution control.but the light will stay on... if it doesnt work put your foot on the brake,car in drive,and give it some gas . if it dies out then u will know that it is the Throtle positioning sensor.if none of this cures your problem its posible that they gave u the wrong camshaft sensor.... u can also check your fuel filter but this might be in the gas tank...

#5 of 12 Re: 2004 Dodge Stratus Camshaft Position [geri24] by misrpiggy

Jul 03, 2009 (12:52 am)

Replying to: geri24 (Dec 29, 2007 2:20 pm)

Hi, did you ever find out a solution to this problem? I've replaced my sensor twice, and with no results so I put the old one back on, after slightly wiping off the end of the cam and it seemed to help for a bit but I am having the problems again.. any help will help. thank you

Replies to this message:

geri24 (Jul 21, 2009 7:13 am)

#6 of 12 camshaft position by deerawz

Jul 20, 2009 (3:55 pm)

Have a problem with my 97 dodge stratus cutting off when stop at a light...changed the camshaft sensor.....and it still dose it.. any ideas on what else could do that.

#7 of 12 Re: 2004 Dodge Stratus Camshaft Position [misrpiggy] by geri24

Jul 21, 2009 (7:13 am)

Replying to: misrpiggy (Jul 03, 2009 12:52 am)

A little while later my timing chain broke and when we fix that it stop doing the other so I guess it was the timing

#8 of 12 IDENTIFY PART by cherokeereg

Mar 08, 2010 (11:22 am)

2004 dodge stratus 2.4L
identify part please
gear that holds the timing belt, while replacing timing belt my son broke some teeth off this gear. I assume it's the upper cam gear, is this correct? need to identify to purchase replacement.
please advise

#9 of 12 2002 stratus 3.0 timeing belt replacement by vairman3

Mar 19, 2010 (9:31 am)

I replaced belt now car is hard starting , and when it starts runs ruff will rev upto about 1500 rpm.after few minuets smooth out somewhat,the crank & cams time marks were lined up.It acts like flooded at first. After run little while it starts to over heat, exhaust manifolds turn cherry red.Can timing be off 180 deg?this is an interference engine.also had to replace tensioner

#10 of 12 06 dodge stratus by jaredyayo

Apr 07, 2010 (2:41 pm)

so at least i'm not the only one. i had the cam sensor replaced on the vehicle not 48 hours later it was doing the same thing. i did the whole unhook the battery and left it off over night. shut the engine light off but not soon after it continued. i don't want another garage to tell me my cam sensor is bad and if its as simple as unplugging something or whipping something off i'm game! any other recommendations are greatly appreciated.

Replies to this message:

fluffysheep (Sep 28, 2012 12:58 pm)

#11 of 12 Re: 2004 Dodge Stratus Camshaft Position [geri24] by hnn1

Aug 03, 2011 (11:39 pm)

Replying to: geri24 (Dec 29, 2007 2:20 pm)

After months with same problem finally I could pinpoint this problem!!!!, in some way cable harness become damaged with a very sharp corner of fuel rail on one of the cables of camshaft positions sensor, I'd remove all tape from harness on this corner (Just where the sensor cables go in to the harness) I check for damage and found one of the cables punctured, so when engine vibation was severe groundind occurs and computer goes into safe mode... solution... I protect this corner wit a plastic cover to prevent future damages and put some tape on damaged cable... computer and car working perfect rigth now and gas MPG goes from 17 to 21.. good luck, hope this help you on solve this issue

#12 of 12 Re: 06 dodge stratus [jaredyayo] by fluffysheep

Sep 28, 2012 (12:58 pm)

Replying to: jaredyayo (Apr 07, 2010 2:41 pm)

When I went in to O'Reilly's auto parts and bought a new cam shaft position sensor for my 02 Dodge Stratus 2.7L The gentlemen informed me I needed to stop back in and have him reset my computer so that it'd register that the sensor was replaced. It seems like a lot of people posting here are having the same issue, I think you guys should find a auto store that does free engine diagnostic on check engine lights because that diagostic reader can reset your computer, too.

« Previous
1
2
Next »
Last

To POST a message, please Sign In.

Forum Tools

Search Forums

Enter Keyword(s):

Browse by Category

Browse by Vehicle

Browse by Board

Browse by Topic

View All Topics

Learn More, Do More

Edmunds Community

Explore Edmunds