Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
Pickups Ford Ranger Ford Ranger Warning Lights and Codes
32 messages, Last post on Feb 24, 2009 at 9:44 PM
You are in the Ford Ranger Forum. Your Host is kcram
|
What is the trouble code for no trouble codes? '02 Ford Ranger has check engine light on, but the OBD code reader which I bought indicates no power in the diagnostic connector under the steering wheel. I checked this with two known working code readers, and got same results. Does anyone have any experience with a bad OBD module, and if so, how do you test it. The truck runs fine. I did take a hit in the tailgate a while back, but cannot say the light came on at that time. I am guessing a problem in the harness, or what the harness hooks to. Any ideas? |
|
| say bank 1 is lean and will not pass air test.what should i do first. | |
| Just replaced a clutch in a 91 Ford Ranger, and now its idling low and doesn't want to stay running. Did a test on it and it said code 14. Does anyone know what this means or how to fix my problem? | |
| I have a 2001 Ranger Edge, 73000 miles, 3.0 Liter, 5 sp, that does not display any codes yet runs rough at idle and will has very little torque, even mildly fish bites during acceleration. Even at hwy speeds, I have to floor the gas to keep it from loosing speed on small hills. The Cats have just been replaced, they were melted, I have driven it with a computer connected, the timing is a little low but at one point the voltages on all three O2 sensors briefly went to zero volts while the truck was running. I have been to the dealer three times and they are like baby sitting pre-schoolers, no help. I pulled a 1200 lb trailer not long ago and the truck would barely pull the thing in 2nd gear, I had to floor it to get it to accelerate at all. Not one here knows what else to do. Is there any help out there? | |
|
|
|
Replying to: roofranger (Oct 09, 2008 2:11 pm) |
|
|
|
| I have 95 Ranger 6 cylinder that upon starting gives 5 beeps 5 times and will repeat if vehicle is driven more than 50 miles at a time on a 50 mile or so regular basis | |
| Does any one know how to read test codes through the EEC test plug. I'm using a volt ohm meter. Do i read a particular voltage and get the code from that? The problem I'm having is the check engine light is coming on and the engine runs rough when this happens. Then the light goes off and the truck runs fine. I changed the fuel filter and have plenty of fuel pressure at the fuel rail. If I'm about checking the codes the wrong way let me know. I went to Auto zone and they only check 96 and up. My truck is a 92 | |
|
I have 06 XLT 4x4 with 5 speed I am looking to change my front bumper to add a winch and also use to tow behind the motor home If you have any good suggestions for one please let me know I am looking for one all ready built . The companies in the off road mags dont seem to offer much from what I've seen Thanks for your help |
|
|
|
|
Don't know what the Ford Owners Manual says about what types of coolant to use or do not use in your cooling system but my MAZDA manual does. I guess the same warnings could apply to the RANGER. The coolant had never been changed in my engine so it was the original installed when I bought the truck NEW. The coolant was was topped off twice in its lifetime. MAZDA didn't do me any favors so I ate the cost of another engine. MAZDA gave me a couple hundred bucks in SERVICE CHITS. A WORD TO THE WISE. DOUBLE CHECK YOUR MANUAL AND DO NOT MIX ANTIFREEZE if your running a 2300. |
|
I have an 05 ranger what does it mean when the overdrive off light blinks
|
|
You are here:
Forums
Pickups Ford Ranger Ford Ranger Warning Lights and Codes
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2010 Ford Ranger
Browse by Board
Browse by Topic
Today's Chats
