Dodge Intrepid Engine

59 messages,  Last post on Feb 28, 2013 at 10:03 AM

You are in the Dodge Intrepid Forum.

What is this discussion about? Dodge Intrepid, Engine, Sedan

#2 of 59 Re: intrepid engine [nexusprime] by andre1969

Nov 04, 2007 (4:16 am)

Replying to: nexusprime (Nov 03, 2007 9:02 pm)
The 3.2 is an American engine, built by Chrysler. It's a smaller-displacement, all-aluminum version of the 3.5 that first came out in 1993. The 3.2 put out 225 hp and was used in the Intrepid ES and Concorde LXI models from 1998-2001, and then was replaced by a reduced hp version of the 3.5.
 
Mitsubishi made a 3.0 V-6 that Chrysler used in their minivans, the Dodge Stealth, and some of the larger versions of the K-cars. Mitsu also made a 2.5 V-6 from around 1995-2000, that was used in the Sebring/Stratus/Avenger/Cirrus midsized cars.

#3 of 59 Crank shaft position sensor by pep5

Nov 26, 2007 (4:53 am)

#4 of 59 Crank shaft position sensor by pep5

Nov 26, 2007 (4:53 am)

Could you please help me find the location of the crank sensor on a 2000 intrepid. a picture would really help. Thanks

#5 of 59 "Too many codes on my '96 Dodge Intrepid" by illini_1_fan

Dec 05, 2007 (1:02 pm)

I have a '96 Intrepid and I have several codes on my car. One of the codes, I knew for sure that needs to be done, but these other codes are just terrible. The codes that I have are: P1784(manufacturer control/transmission), P0401(EGR flow/insufficient), P1698(Manufacturer control/auxillary inputs/auxillary outputs), P0736(reverse ratio/incorrect). Is there anyone out there that can help me find the true problem that I am having with my car? I have had the pulley replaced due to the fact that the barriens were gone in it, the water pump, and alternator replaced already. PLEASE HELP ME!!!!!!!!!

#6 of 59 1994 dogde intreped by rickkim01082

Dec 30, 2007 (1:06 pm)

have a 1994 dodge intreped has no spark and wont start replaced the crank sensor and the coil pack still no spark no start anyone have a clue to whats wrong

#7 of 59 2000 intrepid tapping noise by alpinelab

Jan 07, 2008 (11:08 am)

hi i have a 2000 intrepid and the engine is making a tappin noise rather loud it seems to be coming from the top of the engine at the front just inside where the oil cap is. i changed the oil and had it flushed i also see its gettin oil up top. its gets faster with more reving. wondering if it might be timeing chain or something would really aprreachiate any opions or if ya need more info just let me know it still works good lots of power ect.. thx for any help

#8 of 59 Re: intrepid engine [andre1969] by fljoslin

Feb 21, 2008 (9:07 pm)

Replying to: andre1969 (Nov 04, 2007 4:16 am)
The pre 1998 3.5L engine is in no way related to the 1998 and later 3.5L or 3.2L engines. The later ones are aluminium block while the earlier ones were cast iron.
The difference between the post 1998 3.2 and 3.5 engines is the cylinder bore.

#9 of 59 1999 2.7 motor for intrepid by lawanda333

Feb 22, 2008 (1:30 am)

Can I change to another motor that will fit into the same car like a differant year that may not cost so much?

#10 of 59 crank shaft sensor on 2000 sebring 2.5 engine by mondaine

Apr 07, 2008 (5:33 pm)

can anyone tell me where this is located :

#11 of 59 Re: 2000 intrepid tapping noise [alpinelab] by raulm

Apr 21, 2008 (4:25 pm)

Replying to: alpinelab (Jan 07, 2008 11:08 am)
if is a 2.7l, be real careful because your timing chain is loosing oil pressure; you need to change timing chain and gears, failure to do it, wiil cause engine to fail because of bent valves. that already happen to me.I had to repl. the engine because the 2.7 is too expensive. i had to use a 3.2 instaead if need more info send an email at raul3331yahoo.com i will be happy to help you. engine swap is real easy and will save a lot of money. it will fit i did it in my 98 intrepid..
To POST a message, please Sign In.

Advertisement

Browse by Category

Browse by Vehicle
   View All Vehicles

Browse by Board
Browse by Topic
View All Topics

Edmunds Community

Advertisement