You are here: Forums Pickups Chevrolet S-10 & GMC S15 Sonoma Chevy S10 - GMC S15 and Sonoma Drive Shaft/Driveline/Axles

Chevy S10 - GMC S15 and Sonoma Drive Shaft/Driveline/Axles

8 messages,  Last post on Jul 20, 2009 at 8:46 AM

You are in the Chevrolet S-10 & GMC S15 Sonoma Forum. Your Host is kcram

What is this discussion about? Chevrolet S-10, GMC Sonoma, Truck

Messages Page 1 of 1 All Messages Displayed

Go To Msg # Search This Discussion

#1 of 8 Chevrolet S-10 Drive Shaft by s10draggin Oct 16, 2007 (8:59 pm)
Will a drive shaft of a '96 single cab long bed chevy s-10 fit a short bed extended cab of the same year and model. Replies to this message: hoodlatch (Oct 18, 2007 5:17 pm) s10draggin (Oct 28, 2007 3:48 pm) hoodlatch (Nov 03, 2007 7:30 am)
#2 of 8 Re: Chevrolet S-10 Drive Shaft [s10draggin] by hoodlatch Oct 18, 2007 (5:17 pm)
Replying to: s10draggin (Oct 16, 2007 8:59 pm) I would think your S-10 long bed is rare. I haven't ever seen a long bed on a S-10 later than 92. To answer your question: the two pice drive shaft on my 97 S-10 extended cab looks the same as the two pice drive shaft on my 92 S-10 long bed. I know their pricey, to replace them you'll have to take out a second mortgage. Replies to this message: s10draggin (Oct 28, 2007 3:48 pm) hoodlatch (Nov 03, 2007 7:30 am)
#3 of 8 Re: Chevrolet S-10 Drive Shaft [hoodlatch] by s10draggin Oct 28, 2007 (3:48 pm)
Replying to: hoodlatch (Oct 18, 2007 5:17 pm) i don't have a long bed. i was just wondering if a single cab long bed comes with a one piece drive shaft. and if it would fit an extended cab shortbed Replies to this message: hoodlatch (Nov 03, 2007 7:30 am)
#4 of 8 Re: Chevrolet S-10 Drive Shaft [s10draggin] by hoodlatch Nov 03, 2007 (7:30 am)
Replying to: s10draggin (Oct 28, 2007 3:48 pm) I have a 92 long bed which was my dad's. Shortly after he bought the truck he found out it had a recall on the drive shaft. It came with a one piece drive shaft which was supposed to be a two piece. Until the dealer corrected it with a two piece drive shaft it wouldn't run right. I guess with a one piece drive shaft on a long frame caused too great of an angle on the u-joints and weaken them. It also had a vibration on take off. At least that's my take on it. I don't know if this information helps or not but in Dad's case two piece drive shaft was the answer for long bed.
#5 of 8 Need rear axle swap by Stonesonoma Jan 14, 2009 (7:23 am)
#6 of 8 Need rear axle swap by Stonesonoma Jan 14, 2009 (7:23 am)
I need to know what all axles fit under my 91 2WD Sonoma. Right now I have 3.73 gears and I'm only getting 13.5-14.8 mpg with the 5.7 TBI it has. I'm looking at 3.08, but was told 2.73 would work as well, although, I can't find either here in Michigan. Any thoughts would be appreciated!
#7 of 8 rear end problems by pdub3 Jul 20, 2009 (8:46 am)
#8 of 8 rear end problems by pdub3 Jul 20, 2009 (8:46 am)
I have been through two rear ends now.Is there a problem with these things towing.I pulled a utility trailer about 1000 lbs while moving out of state.Probably put 2000 miles on it doing this.Plan on putting a new ring and pinion set in it.

Messages Page 1 of 1 All Messages Displayed

Go To Msg # Search This Discussion

You are here: Forums Pickups Chevrolet S-10 & GMC S15 Sonoma Chevy S10 - GMC S15 and Sonoma Drive Shaft/Driveline/Axles