Last post on Dec 05, 2013 at 11:56 AM
You are in the Ford Windstar
What is this discussion about?
Ford Windstar, Car Safety, Van
#53 of 75 Re: Van stalls intermittently along with belt squeal [delawarejim]
Jan 23, 2012 (9:10 am)
Thanks so much for your post a the procedure to change the sensor. I am based in Canada and have a 2003 Windstar with exactly the symptoms described in your post. Please let me know if "Crank Angle Sensor" is same as "Crank Sensor" ? Because when I called the dealer he was only aware of Crank Sensor and not the other.
#54 of 75 Re: Van stalls intermittently along with belt squeal [rkarki]
Jan 23, 2012 (11:15 am)
my name id Manuel and had a problem with my 2003 windstar.
In respons to you question, I'm sorry but on't have any information to share with you. I had to take it to a mechanic and he took care of the problem.
Jan 29, 2012 (8:50 am)
hello, I have a 94 windstar, I am dealing with the electrical problems the van is well known for but my biggest problem is that when I first crank the van it will not go, it acts like it's not getting fuel and spits and spatters, i can have the gas pedal all the way to the floor but it will not go and then all of a sudden it will run fine....but if I let it run for 20-30 mins before driving it runs fine until I cut it off and let it sit for a few mins. then sometimes when I use it at first it sounds like it gets stuck in a gear but then after it warms up it won't do that anymore... what in the world is causing this to happen?
#56 of 75 Re: vans stalls at first [freakyfordvan]
May 28, 2012 (12:30 pm)
Same problem with 2002 windstar. Did you ever solve your problem?
#57 of 75 2001 Windstar chirp and die
Aug 27, 2012 (7:55 am)
Some of this seems a bit redundant. Starts fine. After 3-5 minutes, when coming to stop, idles down, chirps like a tiny belt squeal (as if the engine were seizing up) and dies where it sits. I have noticed this occurs whether the van is in gear at a stop light, or in park in a driveway. On the most recent occurrences, the vehicle has also been on a slight upward incline. It will start again, seemingly as if there were never an issue. It happens with decreasing frequency as the van gets to normal operating temperature. I have noticed recently that my drivers side window switch will ignore me intermittently when I try to put my window up. Not sure this is related. An additional piece of info is that the van seems to accelerate and run like poop at low speeds, kind of noisy, straining, as if compression is bad...but once up to speed runs nicely, with no performance issues. It is an SEL, with only 76,000 miles. It was VERY well cared for, and the interior is like new, with many amenities, which is why I would love to make this thing be reliable and trustworthy again. I have read the posts about the crank sensor, IAC, PCM relay, Fuel switches, etc. What I am hoping for is some FEEDBACK or new post from someone who has finally figured out this problem, and could help me not waste money on shot in the dark repair techniques. Thank you for helping!
#58 of 75 Re: 2001 Windstar chirp and die [zachsdad777]
Aug 29, 2012 (3:38 am)
If any of your symptoms include a noise that sounds like a fan belt squeal, then your issue is the crank sensor. It has a bushing that goes dry. This causes the squeal noise and throws your engine timing off which will sputter and stall the engine. If you want a way to test that crank sensor, I would take the black cap off and spray some lubricant into this area.....that should loosen that bushing and you should see an immediate improvement. By the way, when you take that black cap off, you are looking at the very top of the crank sensor assembly. If you remove the whole assembly, it is about 10 inches long and goes deep into the engine area. The busing that goes bad is almost at the very top of this assembly and a shot of WD-40 sprayed into it will tell you if this sensor is your culprit. Best of luck to you, Jim in Delaware.
#59 of 75 Re: 2001 Windstar chirp and die [delawarejim]
Aug 29, 2012 (7:18 am)
Thanks, Jim. In my heart, I was always leaning toward the crank sensor, because of the short squeal associated with the stall. I kind of figured that the problem would not present itself at higher speed, because a bad bushing would be less apparent due to the higher RPM. What I was struggling with was the fact that once the car is warmed up, it seems fine, no matter what RPM. This issue only seems to occur during the first 10 minutes after a cold start. That fact led me to think IAC or some other malfunction in the throttle body. I threw away $28 at Autozone the other day, as the 2 "pro's" just KNEW it was the TPS. Didn't do a thing. I am all too happy to swap out sensors and gadgets at $50 a pop as they are easy, but am not looking forward to getting all greasy and icky replacing the synchronizer. I am going to do it, though. I will post results in hopes that someone else may be helped, although one assumes all the issues in this forum have been resolved, based on the age of the posts. Thanks again! Tim
#60 of 75 1999 for winstar
Sep 03, 2012 (11:28 am)
this van will stall after running fine for aprrox. 45 minutes, sometimes will start right back up. usually you have wait about an hour for it to restart, turns over fine, what the ???? any answers?
#61 of 75 ford windstar starts and dies
Nov 09, 2012 (4:20 pm)
hi we have a 98 ford windstar lx, when we go to start it up the engine dies, no check engine light is on, we have had the coil spring replaced, withe the intake manafold replaced, no vacume leak, fuel filter replaced, brand new spark plugs put in as well, but it does the same thing still
#62 of 75 99 ford windstar 3.8L
Dec 04, 2012 (11:29 am)
hello. i am new to this so please excuse me.. i have a 99 ford windstar that will click multiple times but will not start. we have replaced several things on the van, but the other the car would only click and wouldn't start.. i finally got it today to click multiple times.. (don't ask me how).. i am thinking i am getting a bad connection on my battery or the starter is bad.. not real sure..
the starter cable going from the starter to the battery had pulled off of the starter which is what made it not start before hand.. we fixed that but yet it still won't start