You are here: Forums SUVs Chevrolet Blazer Chevrolet Blazer Engine and Performance Problems

Chevrolet Blazer Engine and Performance Problems

142 messages,  Last post on Nov 11, 2009 at 9:09 PM

You are in the Chevrolet Blazer Forum. Your Hosts are steve_ & tidester

What is this discussion about? Chevrolet Blazer, SUV

Messages Page 9 of 15 1 ... 6 7 8 9 10 11 12 ... 15 Prev Next Last

Go To Msg # Search This Discussion

#81 of 142 Re: Melted vacuum lines [hayesatlbch] by repairdog Feb 10, 2007 (4:34 am)
Replying to: hayesatlbch (Feb 09, 2007 1:29 pm) Sounds like the ignition module (1x2" IC pack). Good luck. You can buy new connectors at many stores.
#83 of 142 MAF on 95 S10 Blazer by sccadsr31 Sep 24, 2006 (6:37 pm)
Can anyone tell me if my 1995 4.3L S10 Blazer Vin W has a MAF and is so where is it located. I have looked and do not see what I generally recognize as a MAF. Thanks David Replies to this message: repairdog (Sep 25, 2006 1:56 pm) sccadsr31 (Sep 25, 2006 8:55 pm)
#84 of 142 Re: MAF on 95 S10 Blazer [sccadsr31] by repairdog Sep 25, 2006 (1:56 pm)
Replying to: sccadsr31 (Sep 24, 2006 6:37 pm) None on 95 - started on 96up with newer injection. You have a MAP sensor or mass air pressure on the manifold. Replies to this message: sccadsr31 (Sep 25, 2006 8:55 pm)
#85 of 142 Re: MAF on 95 S10 Blazer [repairdog] by sccadsr31 Sep 25, 2006 (8:55 pm)
Replying to: repairdog (Sep 25, 2006 1:56 pm) Thank you and does the MAP sensor need cleaning like the MAF?
#87 of 142 Pulling module from inside distributor by lynderae Feb 23, 2007 (2:29 pm)
I am trying to pull the module inside the distributor. The problem is when i took the rotor out the module is under something metal. Do I have to remove the whole distributor to remove it or is there something I am missing. Replies to this message: repairdog (Feb 24, 2007 3:51 am)
#88 of 142 Re: Pulling module from inside distributor [lynderae] by repairdog Feb 24, 2007 (3:51 am)
Replying to: lynderae (Feb 23, 2007 2:29 pm) The cam sensor has 2 torque screws that hold it in BUT the dist position only allows 1 spot where the sensor clears that rotating asembly so you can bump the starter till it lines up or remove the dist. This is 96up so if older model and its the ignition module thats a diff story.
#90 of 142 is it true i can diconect the battery and the computer codes will clear ? by thesweetrosslg Aug 23, 2007 (12:04 pm)
Was wondering i know i have read it around here somewhere but not sure i also heard from a friends that if i dicounect the negative batter terminal and leave it unpluged for like 20 minuts it will clear my computer I just replaced the MAF sensor and am wondering if this is true becouse i need to get that Nasty Service Engine Soon Light of thank you   ross.g Replies to this message: ajaks (Sep 28, 2007 8:21 am)

Messages Page 9 of 15 1 ... 6 7 8 9 10 11 12 ... 15 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums SUVs Chevrolet Blazer Chevrolet Blazer Engine and Performance Problems