Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
Pickups Dodge Dakota Dodge Dakota Radiator and Cooling Problems
61 messages, Last post on Nov 28, 2009 at 10:58 AM
You are in the Dodge Dakota Forum. Your Host is kcram
heater barely blows warm air..never hot. have replaced thermostat, temp gauge reads same as before. coolant level always good, doesn't leek. any advice welcome.
|
|
|
Replying to: manamatt (Jan 13, 2009 3:05 am) I did this and it worked great. I went from having little to no heat on a cold morning to having to turn the heater down because it was too hot. It still takes the truck getting to norm operating temp to get the heater that hot, but it does work. Hope this helps. Cheers, Omen |
|
|
1998 Dodge Dakota, 4-Cylinder, Stock I recently noticed that during the cooling cycles the car goes through from going to ~210 down to ~185 (when the radiator fan is on), a significant amount of steam (I think) is produced from the radiator. I initially noticed this when I turned off my car and got out to see steam coming from the grill. It is not enough to see when the car is moving, but if the radiator fan is turned on at a stop light, you can see steam coming out from under the hood. The engine never overheats! When I open the radiator cap, coolant is filled to the brim. The reservoir also indicates a sufficient amount of coolant. Oil level is slightly low, right on the "add" line. Is this something I should be worried about? Again, the engine doesn't overheat. Thank you.
|
|
|
Replying to: DeLorean (Jan 15, 2009 3:37 pm) If there is around 13 pounds of pressure and there is no signs of coolant loss, either from the radiator or the coolant expansion tank, you are probably experiencing steam from the collection of moisture under the hood or possibly snow, if you live in a snow climate. I wouldn't worry about it, but would monitor the expansion tank for signs of coolant level change when cold. If there is little or no pressure released when the radiator cap is removed, the cap is likely defective. In this scenario the steam you see is probably hot coolant vapors being released. Over many cool down cycles you will notice coolant loss in the expansion tank. the fix is to replace the radiator cap. Best regards, Dusty |
|
|
I'd like to do a total cooling system flush on my '97 Dakota 2WD (V6/3.9L). Should I just following the basic procedure suggested by the Prestone flush kit, in which you add water to an in-line Tee (hose going to heater core inlet) and open drain at the bottom radiator, etc.? Or there a better way that requires - in addition - removal of one or more plugs in the engine block itself? Any thoughts are appreciated.
|
|
|
Replying to: tommy97 (Jan 24, 2009 2:24 pm) For low pressure flow flushing, the engine block drain plugs do not need to be removed, however, they will need to be removed to completely drain the engine of coolant. If you are real fussy...or "anal" as my kids would say, you should use distilled water instead of tap water when replenishing the coolant. I know, this is not typically done, even at automotive repair centers and tap water is probably adequate for most vehicles within the expected lifetime of the cooling system parts. But tap water can contain minerals that may be corrosive to internal engine and cooling system parts. It depends, of course, on any particular water supply. Best regards, Dusty
|
|
|
Replying to: dustyk (Jan 25, 2009 11:35 am) Your point about distilled vs. tap water is well taken, and one I'm well aware of. Tap water, while not ideal, is most practical. When all's said & done, it sounds like the "upwelling" approach (forcing effluent up & out of the radiator fill port under pressure) is the best all-around way. As a side curiosity, regarding the radiator drain plug, if a guy wanted to open it, is there any easy way to do so? I looked a couple times and it seems to be well hidden and disguised. Is there a special "hat trick" involved to access it?
|
|
|
Replying to: tommy97 (Jan 25, 2009 5:30 pm) Regards, Dusty
|
|
|
Replying to: dustyk (Jan 25, 2009 7:36 pm) On a final point, what was driving this whole thing was the sad circumstance in which a couple years ago I lost virtually all heating. My heater core is toast and this was no doubt due to my lame failure to ever flush my coolant. This even contributed to my water pump failing (bearings/seals) at about 8 years (57590 miles). So - what to do about the clogged heater core? I'm sure you know what's involved in removing it from the Dakota so let's not even go there. In exploring/searching/surfing the 'net, I stumbled onto what I believe may be the very next best thing: Thoro Flush by Irontite (Kwik-way): http://www.irontite.com/store/index.php?main_page=product_info&cPath=1&products_- id=4&zenid=1ca29354381138950675c2b8b7603f95 According to its manufacturer, this industrial strength product has been successfully used on diesels and heavy duty trucks. The one-pint jar is actually a powder which is mixed on-site to the recommended specs (using very hot water). You then isolate the heater core by cutting/disconnecting the feeder hoses and circulating the Thoro Flush solution in a backflush direction for about 10 minutes or so. It's supposed to work miracles ... This, my friend, may be the only "solution" to this problem, short of the miserable task of removing the core from under the dash. What say you? Have you ever heard of/used Thoro Flush?
|
|
|
A couple years ago I lost virtually all heating. My heater core is toast and this was no doubt due to my lame failure to ever flush my coolant. This even contributed to my water pump failing (bearings/seals) at about 8 years (57590 miles). So - what to do about the clogged heater core? I'm sure many of you know what's involved in removing it from the Dakota so let's not even go there. In exploring/searching/surfing the 'net, I stumbled onto what I believe may be the very next best thing: Thoro Flush by Irontite (Kwik-way): http://www.irontite.com/store/index.php?main_page=product_info&products_id=4&zen- id=1ca29354381138950675c2b8b7603f95 According to its manufacturer, this industrial strength product has been successfully used on diesels and heavy duty trucks. The one-pint jar is actually a powder which is mixed on-site to the recommended specs (using very hot water). You then isolate the heater core by cutting/disconnecting the feeder hoses and - with the heater turned ON - circulating the Thoro Flush solution in a back flush direction for about 10 minutes or so. It's supposed to work miracles ... This may be the only "solution" to this problem, short of the miserable task of removing the core from under the dash. Has anyone ever heard of/used Thoro Flush? |
|
You are here:
Forums
Pickups Dodge Dakota Dodge Dakota Radiator and Cooling Problems
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2010 Dodge Dakota
Browse by Board
Browse by Topic
Today's Chats
