You are here: Forums Sedans Chrysler 300M Chrysler 300M Engine Problems

Chrysler 300M Engine Problems

23 messages,  Last post on Oct 29, 2009 at 12:52 PM

You are in the Chrysler 300M Forum. Your Hosts are pat & karens

What is this discussion about? Chrysler 300M, Engine, Sedan

Messages Page 2 of 3 1 2 3 Prev Next Last

Go To Msg # Search This Discussion

#4 of 23 Re: Engine problem [beckys] by dwightad Aug 13, 2007 (9:50 pm)
Replying to: beckys (Aug 13, 2007 5:22 pm) Thanks for the info. I took it again to another mechanic and he also stated that it might be rods or the crank shaft. The timing belt/brackets suggestion is a new one for me. Yes, it is very costly. I recently took out an extended warranty on this vehicle so my deductible is only $100.00... I will keep you informed. Replies to this message: shalley (Dec 07, 2007 7:56 pm)
#5 of 23 Re: Engine problem [dwightad] by mikec8 Sep 24, 2007 (3:36 pm)
Replying to: dwightad (Aug 12, 2007 8:57 pm) Similar problem in a Caddy my wife drove. Turned out to be a belt pulley with bad bearings. I can't recall if it was the belt tensioner wheel or another pulley. Luckily, it was easily accessible and not very costly to replace.   Good luck.
#7 of 23 Engine Jerking???? by lovea300m Oct 29, 2007 (5:22 pm)
My 2002, 300M engine starts jerking between 2 and 3 RPMs. What could be the problem? Replies to this message: bswatson (Mar 09, 2008 3:07 pm) ihelget (Mar 09, 2008 8:51 pm) bswatson (Mar 10, 2008 6:09 am)
#8 of 23 Re: problem with my 2001 300m [revok1] by lovea300m Oct 30, 2007 (6:14 pm)
Replying to: revok1 (Aug 09, 2007 11:34 am) My car is slugish or it jerks whatever you want to call it. When you take off and the needle gets up between the 2 & 3 RPMs it starts jerking back and forth. Or do you call it slugish. I have taken it to a Dealership and had a diagnostic test. They arent sure what it is. It could be 3 different things. Timing Belt, Fuel Pump, or possibly drive plate. So much for a diagnostic test. What a waste. I would really like to know. I love this car. It only has 73,000 miles on it. Now the check engine light is on of course until we fix the problem. If anyone out there knows what it is or they have had some experience with the same thing please let me know. Thanks
#9 of 23 Re: Engine problem [dwightad] by shalley Dec 07, 2007 (7:56 pm)
Replying to: dwightad (Aug 13, 2007 9:50 pm) just had the 3.5 engine in my 2003 300m rebuilt at the dealer overlap bearing on the camshaft i now get 14 m per gal and the motor vibrates when ideling in gear at a stop a lot of weird sounds under the hood that i work at the plant that built this garbage so much for buy what you build by the way this car only has 81000 kilometers on it
#10 of 23 99 300m stalling problem by ihelget Jan 08, 2008 (11:23 pm)
My car will all of a sudden stall. it usually happens when i am just about stopped. i can put in neutral and start it back up but it is getting annoying. also when i am driving at highway speeds it will some times feel like it chugs. i have done a fuel system cleaner and that didnt see to help at all. is there any explanation for these things?
#11 of 23 300m rack and pinnion by ihelget Jan 08, 2008 (11:26 pm)
My rack and pinion just went out in my car i was wondering if it is a difficult fix or if it is something that i could do my self.
#12 of 23 Engine stalls by duffer65 Jan 10, 2008 (9:39 am)
#13 of 23 Re: Engine Jerking???? [lovea300m] by bswatson Mar 09, 2008 (3:07 pm)
Replying to: lovea300m (Oct 29, 2007 5:22 pm) try using your key code to see if there is a fault code.put your key in the ignition turn on to run but dont start.do three times on,off,on,off,on.you should see a code where your trip meter is.i have a 2002 300m and it did same thing.i got a p0206 fault,which is an injector 6 circuit fault.runs like a 300m now. Replies to this message: ihelget (Mar 09, 2008 8:51 pm) bswatson (Mar 10, 2008 6:09 am)

Messages Page 2 of 3 1 2 3 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Sedans Chrysler 300M Chrysler 300M Engine Problems