Last post on Apr 04, 2013 at 12:58 PM
You are in the Chrysler/Plymouth Voyager, Dodge Caravan
What is this discussion about?
Dodge Caravan, Chrysler Town and Country, Plymouth Voyager, Van
#29 of 37 06 grand caravan power door locks
Aug 19, 2010 (11:26 am)
Anyone have a problem with power door locks that stopped working?
#30 of 37 '08 T&C EGR replacement
Sep 19, 2011 (11:01 am)
This looks like a great site for repair help. I am getting code PO404. I think I have located the EGR valve on my 3.8L . It is on the drivers side rear bank near the spark plug wire distribution connections. I don't want to break anything but I can't get the electrical connector off. I did slide the red lock tab to the right. The connector should just pull off...is that correct ? or are there more locking devices on this connector ?
#31 of 37 EGR Racket
Dec 26, 2011 (12:06 pm)
I called a garage after my "check engine soon" light came on. I asked them what is meant and they said we will charge you $130 for a diagnostic and then the cost of parts and repair. I went to autozone and they tested it for free and got code PO 400 which is for EGR valve. They said they has one and it was $120 and I could put it in myself with littke mechanical skills. I called garage and asked them hypothetically if it was a EGR valve what would I be looking at turn key. He said $130 for diagnostic, $229 for ERG and $80 for installation. Total $439.00. I went back to auto zone with my tools and bought the part, put it in, and even had them confirm that the diaphram was bad. They reset my engine light and I put 100 miles on and then got my inspection sticker. I saved $319 and, as I had a free oil change coupon from the first garage, got my oil done for free. He noticed the new inspection sticker and the new EGR and asked why I didn't have them do it. I explained that I did it myself and saved $319 and thanked him for the free oil change!!! He was pissed...imagine that!
#32 of 37 procrastination works too
Dec 26, 2011 (12:41 pm)
How do you reset the light? I never did swap mine out. It supposedly doesn't effect much (I haven't noticed) it's been about 3 years since it came on. I should probably swap it out though.
#33 of 37 Reset oil service light Chrysler Town and Country
Sep 10, 2012 (12:36 am)
Full procedure how to reset oil service light Chrysler Town and Country. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Chrysler cars. Or any warning light for service reminder which appears on the display.
Info pictures whit the steps
#34 of 37 Re: '08 T&C EGR replacement [dsurek]
Apr 04, 2013 (10:33 am)
I have the exact same issue as post #30 on this- as Dsurek on this same vehicle -how do you disconnect the connetor from the EGR valve- I also slid the red tab to the right to disengage, but the connector still seems quite stuck - anyone have a suggestion or a video that shows this
#35 of 37 Re: '08 T&C EGR replacement [joef123]
Apr 04, 2013 (11:48 am)
I have replaced my EGR valve myself. It is difficult to get one because it is a dealer only item ($94). Places like NAPA may have a listing but soon find they can't get it. When I slid the red tab to the right this time, it came out and the plug almost came off by itself. Leave the pipe connected to the EGR vale. Remove the screws for the pipe in the valve cover and a hold down bolt from the pipe bracket. Pull out the 3 rear plug wires and brake vacuum hose out of the area. I also disconnected the negative battery cable and put a rag over the positive. Remove the two bolts holding the EGR valve and remove the valve and pipe at the same time. Now it is easy to remove the pipe from the EGR and put it on the new EGR with a new gasket. First I spayed some cleaner through the pipe and wiped out the gunk as best i could. I put some compressed air through it to blow out any debris. Clean up the area where the new EGR will mount and install with the new metal gasket. Put the three rear plug wires #1,3,5 back on. Put the power brake vacuum hose back on. Put the connector and red tab back on. Buy or borrow a scan tool to erase the code and that's it. So far, so good, no codes coming up. It was about a 2 hour (three beer) job.
#36 of 37 Re: '08 T&C EGR replacement [dsurek]
Apr 04, 2013 (12:03 pm)
Thanks for the reply - I figured out the connector and I have a 2009 van - I think the EGR valve got rotated 180 in the 2009, as it is on the drivers side and I see one bolt that will be a challenge, but I think accessible with a universal joint - I also found several sources online for the 2009 EGR valve, and it was about $85 shipped to my door - I would agree - it looks like a 2-3 hour job for a Saturday afternoon - I have sprayed all the bolts with PB blaster already for it to have a few days to make the bolts easier to come off in a few days when the part arrives -
Thanks for the reply
#37 of 37 Sensor controlling EGR valve on '02 Caravan eC 4-Cyl.
Apr 04, 2013 (12:58 pm)
What sensors have input to controlling the EGR valve operation?
Van missfires/surges on flat roads under high vacuum and spark advance conditions, when barely "off throttle." It's so bad, we don't drive van on flat interstate highways; only secondary hilly roads when this problem isn't noticeable.
-Disconnected EGR valve and symptoms disappeared
-Replaced EGR valve, solenoid, etc. with new assembly and rehooked and symptoms returned.
-Disconnected EGR valve and symptoms disappeared
Problem must be with something giving input to the main computer controlling the EGR valve.
Any suggestions on a sensor or controller that could be bad?