Ask the Car People.SM


After Market DVD screen installation

15 messages,  Last post on Mar 17, 2011 at 2:47 PM

You are in the Chrysler Pacifica Forum.

What is this discussion about? Chrysler Pacifica, Wagon

Messages Page 3 of 3

#12 of 15 Re: I did this with our 2007 model - It can be done! [pierremicha] by jmacsellnu

Nov 30, 2007 (4:55 pm)

Replying to: pierremicha (Aug 21, 2007 11:12 pm)
I have a 04 with the 6 disk dvd/cd changer also....i took the left pillar off and saw the same wires and skinny one and a thick one....i could not trace them too far because they went farther back then i could feal them.....have you found anything out with your to get it to work????need help bad

#13 of 15 DVD Player by chypacifica

Aug 21, 2009 (6:54 am)

I have a 2005 Pacifica with a 6 disc CD Changer factory unit. I tried connecting the aftermarket monitors that go on the headrests but could not get any video to those monitors. I installed a DVD and heard it fine on the radio speakers but nothing was playing on the monitors. I have seen alot of discussions on here and it sounds like all I need is a wiring harness, is that true?

#14 of 15 Re: I did this with our 2007 model - It can be done! [jmacsellnu] by helpdvdquest1

Jun 15, 2010 (6:51 am)

Replying to: jmacsellnu (Nov 30, 2007 4:55 pm)
What you need is the (overhead) wiring harness, thats what everyone on this post needs if you have the 6 disc dvd with no monitor and want to install the monitor, but thats not the only wires you will need.
 
Trying to figure this out has not been very easy. There are several wires that you need. This place has the (overhead) wiring harness but its 214 bucks. http://www.chryslerpartscenter.com/partlocator/index.cfm?action=getJointLocator&- siteid=215327&chapter=&Sectionids=0,2648&groupid=2657&subgroupid=2658&componenti- d=0&make=7&model=Pacifica&year=2006&graphicID=NS04295&callout=3&catalogid=2&disp- layCatalogid=0
 
This site has a full of list everything that you will need and actually how to do the install http://starparts.chrysler.com/info/default/k6858779.pdf
 
For wires you will need number 2, (overhead harness), number 7 (extension harness), number 9 (power harness), number 10 (jumper harness) number 17 rev.rdv jumper harness.
 
All of these wires are not cheap. I found number 9 (power harness) on ebay for 75 bucks. You will also need the (stud colar fastners) number 4 and number 6 (hex nuts) to secure the dvd monitor to it in and make sure that that plate is up in the headliner to fasten and secure the montior to before you go cutting.
 
If anyone knows of a cheaper place to buy all of these parts from please let everyone know.
 
I got the dvd montor off of ebay for about 100 bucks.
 
Good luck

#15 of 15 Re: I did this with our 2007 model - It can be done! [helpdvdquest1] by huffmanfamily

Mar 17, 2011 (2:47 pm)

Replying to: helpdvdquest1 (Jun 15, 2010 6:51 am)
I am hoping someone can help.
We have a 2007 Pacifica Touring. Has cd deck and separate dvd player. We have had an after market monitor installed (power acoustik). Currently video works, sound works through car speakers (not RF). Wireless headphones will pick up the sound, but driver can still hear the sound even with headphones activated.
 
I am trying to get this vehicle to operate dvd system separate from cd/radio using headphones. Can get system with Pacifica remote to show headphone mode on control panel, but can still hear sound in car. Also, when I change mode after putting in headphone mode to go to radio for example, power is cut from DVD player.
 
I thought this vehicle was equipped for the rear to watch movie and use headphones while driver could listen to radio.
 
Can anyone help???
 
thank you in advance!

Messages Page 3 of 3

To POST a message, please Sign In.

Advertisement

Browse by Category

Browse by Vehicle
   View All Vehicles

Browse by Board
Browse by Topic
View All Topics

Edmunds Community

Advertisement