Last post on Apr 29, 2013 at 1:49 PM
You are in the Mazda 626
What is this discussion about?
Mazda 626, Lights, Auto Repair, Electrical, Sedan
#16 of 31 charge and rear light warning is lit, what does it mean?
Nov 08, 2009 (1:53 am)
I have a 1992 626 mazda, the battery died and replaced it two days ago. Upon replacing it i noticed the warning lights "charge" and "rear" is on. What does this mean? Could this be link to my alternator needing replacement or is it totally different prob? Im suspecting my alternator is gone, cos when my car is on idle i only get 12.9 V?
#17 of 31 Re: car wont start [spaceboy123]
Mar 26, 2010 (11:03 am)
I have the same problem with the same year 626. Did you find a solution?
#18 of 31 Poor Idling , sometimes engine stops
Apr 22, 2010 (3:12 am)
This is a 1989 Maz 626. Switches off when you slow down or stop. Have chaged fuel filter , oil filter , plugs and air filter , oil. Can not fix source of problem. Can any one help?
Nov 15, 2011 (12:28 am)
I had 2 problems and fixed one but the other still exists. When my head lites are working, all is fine, but when the head lites go out by themselves, the parking lites are still on, the high beam indicator is on for both high and low beams and the windshield wipers come on without being turned on. when the head lites come back on by themselves, the wipers stop and all is normal.
I have checked all fuses and do not find a relay for the head lites. I have banged on the fuse box and tapped hard on the wiring coming from the head lites including the main harness. I banged on the head lite switch and ignition switch and nothing seems loose. no wires seem to be loose or plugs to wires everywhere don't appear to be corroded. I banged on bodyparts under the hood, but nothing points to an answer. the lites don't stay on very long before they go out for no reason.
My next step will be to look for ground wires to see if they are corroded or barely hanging on, but the visible ones didn't react when I banged on them hard.
Please let me know what you think. Thanks, Mr. B
#20 of 31 Re: 1994mazdaowner [1994mazdaowner]
Dec 24, 2011 (9:09 pm)
Your light switch may be defective. These switches have internal sliding contacts and they can malfunction internally without any visible loose wires or corrosion.
#21 of 31 Re: 1994mazdaowner [p100]
Dec 26, 2011 (9:43 pm)
As stated in my question posted, I was going to investigate the grounds to the headlights. At first I hooked a ground to one of the two thick wires and the headlights came on. Not going any farther for that evening, I just made it a temporary connection. Turned out to be the pos wire to the high beam. I had to make sure not to put the high beams on while driving. Later I went to an auto parts store and they had a manual on my year Mazda, so I looked up the wiring diagram for the headlights and found out that one of the thinner wires, the black with yellow tracer, was the ground for both beams. Being surprised that such a thin wire was the actual ground, I moved the ground wire to the black with yellow tracer and now have everything back to normal. Somewhere there is a plug that takes that black with yellow tracer to ground, but I didn't figure out where. Guess I'll just be happy to have headlights now and will consider that the switch you refer to, is where the ground originates from.
Thank you for the info. My car runs great now and I will be taking it on a long distance trip to Miami soon. I will have a better chance to look everything over real good in the better climate.
Thanks again for your help. Sincerely, William Lichvarcik Sr. 216-240-2000
#22 of 31 Re: charge and rear light warning is lit, what does it mean? [oliverc]
Apr 09, 2012 (9:20 am)
i have the same probleme did you solve the probleme and what whas the fault please help
#23 of 31 Re: charge and rear light warning is lit, what does it mean? [antonvs]
Apr 09, 2012 (8:09 pm)
I went to advanced auto parts and looked in the book for MAZDA 626 and looked up the ground wire colors in the headlight area. Once i found the ground, I tapped into the ground anbd made another connection to ground on my own. I suggest that you find the ground side of whatever is not working properly and tap into it and touch ground with it and see if that fixes it. GOOD LUCK, Bill
Jul 08, 2012 (7:16 am)
Its been a long trouble free time since my last post here. My wifes 94 626 LXA ATX Air Bag started lighting up last month. It flashes then stops then flashes again. Never stays on solidly.
Car has 88K miles on it and is in Athens Greece.
I cleared the codes with the battery disconnect step on brake pedal for 10 seconds trick. This stopeed it from flashing for a day and I
Brought it to a Mazda guy who tried to run diagnostics on it and it showed no codes.
It was not flashing when I brought it, and now 2days leter its flashing like crazy. He asked me if the I4 is a FS V or FS1 I did not know the answer. The 93 is a Ford EEC IV ignition so I dont think he will ever get any codes.
Unless the airbags are different from the OBD 1 system the only way I ever got codes in 10 years is the OBD1 jumping wire technique, and reading check engine light pulses
Any ideas ?
Does anyone know what the 1993 626 LXA I 4 engine is . Here is Vin if that will help
He said when light flashes that means airbag will not open. I am afraid it will open when wife is driving it . Is he correct ?
My wifes uncle said that flashing light means a sevice reminder based on age/mileage and mazda can reset it . I thought the battery disconnect would do it but its back so is there any way to reset it , or is it defective for real
#25 of 31 Air bag light on
Sep 20, 2012 (10:07 pm)
somehow my mazda 626 (1996) air bag light turned on and after consulting many electricians and their diagnoses, could not turned off the light. can someone help me that what to do.