Last post on Oct 28, 2013 at 4:35 PM
You are in the Jeep Cherokee and Jeep Grand Cherokee
What is this discussion about?
Jeep Grand Cherokee, Jeep Grand Cherokee SRT-8, Jeep Cherokee, Engine, SUV
#615 of 731 1995 grand jeep cherokee laredo.
Oct 05, 2010 (10:45 am)
my jeep needs an engine according to mechanic. It overheated and apparently there was no water in radiator. Its frozen. first of all hes charging me 1,800 to replace engine.Prior to this the computer kept stating coolant engine low. I would put water in it. Then it would say coolant sensor bad. It had been saying this for months now. I would put water in it. It was also dripping water from bottom, but i kept putting water in plastic container that connected to radiator. Thats when it broke down on the freeway. My husband told him to take as long as it takes. Has anyone had this done and is the price reasonable and how long should the duration be for repair. any advice. I would appreciate it!!!
#616 of 731 Re: 88 Cherokee Inline 6(5 Speed Manual) [gscott424]
Oct 20, 2010 (4:47 am)
First after checking and replacing all normal PM parts, Fuel Filter, Plugs, Cap, Wires AND AIR FILTER, if this does NOT cure the hi-load sluggishness, its your Catalitic Convertor. Replace it - or eliminate it.
Best test - most economical - is to disconect eahaust engine side of convertor and go do your hill climb.
Gonna be a bit noisy but if this cures it your Convertor is what is called BLINDED - Plugged.
#617 of 731 2000 jeep cherokee sport 4.0 High oil pressure
Oct 26, 2010 (8:20 am)
I changed the oil put in 20w-50 after that i noticed the first 15 min of driving the oil pressure shot up to 80psi after 15 min the oil pressure is normal so I changed the oil back to 10w-30 put in a k&n filter and it still does it, could I have messed up the sending unit or is the oil relief valve stuck I had a new oil pump installed 2 yrs ago
#618 of 731 Re: further to my previous message [indianajames]
Nov 07, 2010 (2:24 pm)
I am not positive about the 94 model, but on the 95 there is no EGR on the 4.0.
#619 of 731 Re: idles fine but boggs when i hit 3000rpm [illdill]
Nov 07, 2010 (2:36 pm)
I just got through putting a rebuilt engine into my 95 Grand Cherokee and found through lots of frustrating trial and error that the 4.0 will run marginally with the distributor a tooth off. This is due to the tip of the rotor being about a half inch long and the timing being controlled by a delay or advance in the firing of the coil. The thing is, when the spark advances too much (at around 3000-3500 RPM) the spark fires to the wrong post on the distributor. This causes major backfiring and a loss of power. While trolling for answers on the internet I found several posts that said that it would not run if the distributor is a tooth off, so I figured that this tidbit of info would be handy to post.
#620 of 731 1994 Jeep Grand Cherokee Door Issues
Dec 20, 2010 (12:30 pm)
Hi. Got the Jeep from my dad. He apparently had problems with the driver door, because it looks like the bottom hinge has been re-welded back onto the door itself. Now, the weld has broken off, and the door doesn't close all the way. My husband had to take the bottom pin out of the hinge, just to get the door to drop into place. It still does not close all the way, but now, the interior lights stay on. I have taken out the fuse for the interior lights, but the console reading lights, and middle console light stays on. Aside from disconnecting the battery, which I have done, how can I get the lights to stay off so it doesn't drain the battery? I am afraid to open the door again, for fear of not getting it to latch so I can use it for transportation. Any suggestions would be greatly appreciated!!
#621 of 731 2007 Grand Cherokee CDI codes: p0087,p0088
Dec 21, 2010 (7:18 pm)
I'm looking for some assistance with the above codes. They are the result of the Electronic Throttle Control warning and check engine like coming on. I've been able to reproduce the codes and warnings with hard acceleration, but also with steady city cruising.
I've reset the codes, numerous times, and also had the codes and check engine light reset themselves!
I've run fuel dryer, and fuel conditioner twice, because i thought I picked up a tank of bad diesel, without results. Latest has been to replace the fuel filter. The codes apparently refer to high and low pressure at the solinoid on the fuel rail. Of course Chrysler won't just sell the solinoid and would prefer I spend $1000 for a new fuel rail.
Has anyone run into this issue with the diesel?
your assistance is appreciated.
#623 of 731 2011 Hemi hesitation/misfire problem
Dec 30, 2010 (12:44 pm)
Recently bought a 2011 Grand Cherokee Limited---between 30-65 mph while maintaining speed or slightly accelerating, engine misfires/hesitates frequently. Service Dept can't find anything wrong---service manager rode with me and felt the misfires---he stated that it had something to do with the cylinders shutting down to save gas and then firing back up for more power. Maybe so but this should not be doing this as much as it is. terribly annoying after I spent so much money on it. Filed complaint with Jeep customer service in detroit. they contacted the service manager who rode with me. they can't do anything unless they find something wrong on the computer---This is nonsense---Something is wrong with this hemi engine and probably with others---anyone else experiencing this problemChrysler customer service