Sign In Join 



Chevy S10 - GMC S15 and Sonoma Accident Damage Questions

12 messages,  Last post on Nov 13, 2007 at 12:15 AM

You are in the Chevrolet S-10 & GMC S15 Sonoma Forum. Your Host is kcram

What is this discussion about? Chevrolet S-10, GMC Sonoma, Truck


Messages Page 2 of 2
1
2
Prev
Next
Last
Go To Msg #
Search This Discussion

#5 of 12
Re: Hit from behind, could driveshaft be damaged? [masterguns] by hoodlatch
Apr 14, 2007 (4:40 am)
Reply

Replying to: masterguns (Apr 13, 2007 8:38 pm)

You might contact the experts at this web site:http://www.troublecodes.net/. They ask a small fee for their expertise but I have the impression they are subject matter experts, unlike a shade tree mechanic as yours truly.
#6 of 12
Re: Hit from behind, could driveshaft be damaged? [masterguns] by gonogo
Apr 14, 2007 (8:16 am)
Reply

Replying to: masterguns (Apr 13, 2007 11:58 am)

U-joints are no big deal, surely not a rebuilt drive shaft. Not too long ago for $7-$8 you could buy a u-joint. All you need to install is a large vice. Seems like everything now is plug and play, nobody want to repair anything any more. All drive shafts have slip joints so during normal suspension movement the shaft slides on the splines.
My 99 Sonoma was rear ended on the Interstate when traffic got backed up about 5 years ago, new bumper and nothing else.
#7 of 12
Re: Hit from behind, could driveshaft be damaged? [masterguns] by kcram HOST
Apr 14, 2007 (9:32 am)
Reply

Replying to: masterguns (Apr 13, 2007 8:38 pm)

You got nailed by a Suburban... that explains a lot. It's all basic physics, same basic concept as whiplash. If you're hit hard enough from behind while your vehicle is stopped, your body is jerked forward from the transferred momentum, then snapped back because the vehicle isn't moving. Same thing happens to the U-joints and driveshaft. The harder you're hit, the more energy is transferred from the collision to those parts.
 
It's always "buyer-beware" after an accident when things seem minor at first. You see some minor cosmetic damage and figure nothing else happened. Then later on, you get the shimmy-and-shake that says something underneath didn't survive, and it's very difficult to justify for the adjuster. I'd recommend getting an estimate from a specialty shop that deals in drivetrain (shafts, axles, U-joints) with an expert opinion as to what caused the damage.
 
kcram - Pickups Host
#8 of 12
Re: Hit from behind, could driveshaft be damaged? [masterguns] by hoodlatch
May 12, 2007 (3:38 pm)
Reply

Replying to: masterguns (Apr 13, 2007 8:38 pm)

Did you ever find a solution to your situation?
#9 of 12
Re: Hit from behind, could driveshaft be damaged? [hoodlatch] by masterguns
May 14, 2007 (6:45 am)
Reply

Replying to: hoodlatch (May 12, 2007 3:38 pm)

Well, apparently, a U-joint was knocked loose in the collision. One of the mechanics at the shop offered to tighten it back on his own time for about $150. My truck runs great now with the same drive shaft it had before which is fine by me. Thanks for asking!
#10 of 12
Re: Hit from behind, could driveshaft be damaged? [masterguns] by darkpunk33
Jun 21, 2007 (9:18 pm)
Reply

Replying to: masterguns (May 14, 2007 6:45 am)

Hey,
 
I was also hit from behind and i'm getting this weird noise as well also gets louder as the speed increases. However did you happen to notice if you got this noise in Reverse? Mine doesnt make the noise in Reverse which pushed me away from the drive-shaft? Anyways this noise is reallly annoying!! Anyways any input would be GREAT!! Thanks
 
Matt
#11 of 12
Re: Hit from behind, could driveshaft be damaged? [darkpunk33] by masterguns
Jun 23, 2007 (8:49 am)
Reply

Replying to: darkpunk33 (Jun 21, 2007 9:18 pm)

I don't recall any noise when backing up. Of course it was a while back and never spend much time in reverse. My advice is get it checked out by two or three places. If they say you need a new drive shaft cuz your U-joints are bad and you don't have the money for it, find somebody to just tighten the joints for you.
#12 of 12
Re: Hit, driveshaft damaged? [gonogo] by philscbx
Nov 13, 2007 (12:15 am)
Reply

Replying to: gonogo (Apr 14, 2007 8:16 am)

gonogo is right. This is how we did for 30 years.
 
Getting hit, the shaft will take up the slack at the tranny, but only if so much movement occurred to move the axle.
 
So this isn't making much sense unless the frame buckled between the axle and tranny to shorten the distance for the drive shaft to bottom out at the tranny and over load the U-Joint at the axle.
 
The only other possibility is the impact and over load with the tires forced the drive shaft to rotate rearranged the rust in the U-Joint bearing cups.
 
You would have to remove U-Joint bearing caps to inspect for the real problem.
1], U-Joints just don't come loose. They have 2 very strong U-Bolts holding them to the yoke of the rear end.
2] Quick inspection with veh on lift will show if there is any movement.
This movement if any will normally be at the bearing cups from worn out needle bearings.
 
60,000 miles on original U-Joints and never serviced prior is probably about right for replacement with a joint and service grease fitting.
 
Now for vibration of drive shaft, it's not impossible it was bent when loaded onto truck for transport. So check for towing damage. I know in this case it was not towed. Just reporting what happens.
 
I've seen U-Joints installed wrong as well.
If they are not seated in yoke correctly and tightened and your accident corrected the seated joint to yoke fit, then yes, Joint U Bolts would be loose.
Otherwise I'd say B/S they were loose at bolts from being hit from behind.

Messages Page 2 of 2
1
2
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics

Today's Chats

Advertisement