Last post on Aug 04, 2013 at 10:40 AM
You are in the Honda CR-V
What is this discussion about?
Honda CR-V, Electrical, SUV
Jun 28, 2009 (10:29 am)
does anyone know how to manually put down power windows? B/c my window is stuck up and motor quit...I need to get it down to fix the motor (replace it) can some one plz help me out?
#22 of 32 Re: 98 cr v [honda_lover1]
Jul 07, 2009 (8:31 am)
You need to purchase the Honda Shop manual. Order form is on the last page of the Owner's Manual or online
#23 of 32 Driver side window won't work!!!
Sep 13, 2009 (7:30 pm)
Got into my 2004 CR-V and used the power switch to roll the window down, but it will not go back up. Still makes the noise so I don't think that it's a fuse, considering the other windows work and it rolled down but not up. ANYONE have the same or similar issues that can help!!
#24 of 32 window goes down, up is problem.
Sep 13, 2010 (4:36 pm)
1997 honda crv, driver window goes down ok, when tyring to raise it goes up a few inches and stops, motor noise stops. I have to lower it down again then as it raises up i have to pull window with hand as it starts to raise and keep force on it untill it is all the way up, motor noise can be heard as i force it up. I looked down into door and saw what looks like a drive chain on window, so i sprayed WD40 on chain, it did not make a difference. Is the motor on last leg? ZOr if i take door interior out is there any adjustment i can make?
#25 of 32 Re: window goes down, up is problem. [barryz]
Sep 16, 2010 (10:22 am)
I can't answer your question but my 97 CR-V driver window is crapping out too. Same symptoms as yours but I think my case is a bit more advanced. Just recently, I am no longer able to manually assist the motored movement of the window. The window now seems as if it is no longer attached to the mechanism. If I grip the window on both interior and exterior, I can move the window up and down without activating the switch. If I activate the switch, I can hear the motor wind though, it just doesn't move anything. I'm considering trying to fix this myself by replacing the motor/regulator. My Honda dealer suggested that I might be looking at $700 max to repair the window - seems excessive. I'm not too mechanically oriented but I found a repair guide/instruction at about.com that gives me some hope that I could repair it myself for much less - the motor/regulator can be found for $100 or less. Here's the link to the repair guide, you might consider it too.
#26 of 32 2002 Honda CR-V
Jul 24, 2011 (8:08 am)
Have a CR-V with power windows. Driver side window does not go up or down. It's in the closed position now. The other three windows work and can be opened and closed by the driver slso.
#27 of 32 Honda CR-V Power Window Problems
Mar 25, 2012 (9:40 pm)
I have a problem with my driver side power window of CR-V 2007 & 2010. If I open the window glass when it is wet, it cannot go up completely. The window glass will go up & down repeatly ended with half or less open. Honda service explained that it caused by dirty window frame then they cleaned up. Though it does not work. Can somebody help? Thanks
#28 of 32 Re: Power window problem [crvme3]
Jul 25, 2012 (5:21 pm)
I to own a 1997 crv I,ve discovered that there is a problem where the wiring plugs into the door The wires have been scored when they were inserted and crimped to the pins of the plug.My vech. had 5 broken wires and while repairing 3 more broke this means that some of these wiresprobably had only afew strands that were connected which would severely limit power available for window motors power locks causeing them to stall under load.I removed the door by removing the door hinge bolts (they are not adjustable at this point so no need to mark etc. )I unplugged the wiring from the door and spliced soldered &shrink tubed each wire and secured them and reinstalled the door no more prob.Prior to this i had power lock & alarm issues too
#29 of 32 Re: 98 crv dr. pwr window will not go down.... [honda_lover1]
Jul 26, 2012 (4:52 pm)
You need to remove the panel on the inside of the door .Take the screws in the armrest out ,also the screw inside the door handle ,remove speakergrill it prys off undue screws holding speakerin ,carefully pry the panel off at the bottom and sides.Lift it to remove it under window,carefuly unplug the wiring ,stip the plastic sheet off you can now undue the 10mm bolts that hold s the window mechanism in the door unbolt the window from the mechanism remove the motor and mechanicals repair and reinstall see my earlyer post re: broken wires at main plug to the door
#30 of 32 power window stuck up in close position
Feb 03, 2013 (7:08 pm)
How can I access to the bolt holding the glass and regulator it is stuck up in close position. There is no hole alloted to unbolt it. The only access was at lower/open position. I can not move or push the window down manually. Any suggestion please.