Mitsubishi Diamante Timing Belt

HI, I also have a Mitsubishi Diamante GDI that I imported from Japan. I order all my parts from autoterminal in japan.

I have a problem that my car is idling and the machines in England cannot read the data to correct the idling. If you know of anywhere in England I would appreciate it.

Many thanks

#8 of 13 Re: plugs [rockster71] by 97diamante

Jul 26, 2008 (4:39 pm)

Replying to: rockster71 (Dec 14, 2007 12:27 pm)

The engine is a V-6. This strongly implies that there are 6 spark plugs!!

The front 3 plugs are easy to replace.
To get to the back 3 plugs, you must remove the upper intake plenum. Just remove the bolts (Several hoses must also be removed and the throttle-body intake hose must be slid off the throttle-body.) and pivot it backwards over the firewall and secure it there while changing the plugs. Use an new gasket when reassembling.
It's not too bad, maybe an hour.

#9 of 13 Re: Diamante timing belt [mikevegas06] by 97diamante

Jul 26, 2008 (4:42 pm)

Replying to: mikevegas06 (Jul 09, 2007 3:49 am)

Another GOOD location for parts is

http://www.rockauto.com/

#10 of 13 Timing belt reset by leihualani

Jan 14, 2009 (1:12 pm)

My old mechanic replaced my water pump and unfortunately due to an unseen issue he was unable to finish the repair of my car. I have another mechanic whose expertise is good but he is a little blown out of the sky when he noticed the last mechanic did not mark the timing belt before it was removed causing the new mechanic to complete the repair. We have had a problem locating a repair manual to reset the belt for me. Where can i obtain this info to assist my new mechanic please. It is nerve recking to share a car. and, that is the only thing he needs to complete to get my car back on the road.

#11 of 13 94 Diamante Timing belt by peter931

Mar 31, 2009 (2:15 pm)

After R&R timing belt on 3.0 L SOHC what some one installed wrong way ( cams 180 off). This engine has no interference.Now I have timing marks on cams and crank in position and #1 piston is in TDC , distributor rotor is in #1 position and engine is still not running on all 6 cylinders .
Any one know where could be the problem ?

Replies to this message:

1998lincoln (Nov 01, 2009 10:06 pm)

#12 of 13 Re: Mitsubishi D Timing Belt [givio] by 1998lincoln

Nov 01, 2009 (10:02 pm)

Replying to: givio (Mar 19, 2007 7:41 am)

I just replaced a timing belt on a 2001 Mitsubishi D,3.5L V6, you will need to replace the water pump as well.The timing belt drives the water pump.
Manufacture suggest replacing water pump!
Also look at your tensioner,it may need replacing also.
Make sure you adjust the timing belt tensioner correctly,or it will cause premuture
belt failure!

#13 of 13 Re: 94 Diamante Timing belt [peter931] by 1998lincoln

Nov 01, 2009 (10:06 pm)

Replying to: peter931 (Mar 31, 2009 2:15 pm)

Someone set the timing wrong, go back and reset the timing using the #1 spark plug!Run the #1 piston to Top Dead Center,and then install the timing belt!
It sounds like someone set the timing using the #4 plug!

« Previous
1
2
Next »
Last

To POST a message, please Sign In.

Forum Tools

Search Forums

Enter Keyword(s):

Browse by Category

Browse by Vehicle

Browse by Board

Browse by Topic

View All Topics

Learn More, Do More

Edmunds Community

Explore Edmunds