Ask the Car People.SM


Toyota Camry Vehicle Stability Control

65 messages,  Last post on Feb 05, 2012 at 10:37 AM

You are in the Toyota Camry Forum.

What is this discussion about? Toyota Camry, Sedan

Messages Page 7 of 7

#57 of 65 Re: VSC/TRAC ENGINE LIGHTS [wwest] by acco20

Jan 24, 2012 (11:01 am)

Replying to: wwest (Jan 23, 2012 10:45 am)
wwest....Unrelated, but I would value your input on this question. In some snow conditions, it would be very helpful to be able to turn off the traction control. My 2001 lexus ls 430 has this capability with a push button on the console. My 2007 anniversary edition Camry hybrid does not have this option. Do you know of a reliable task that can acomplish this without harm to the other components, even just until the car is started again. I value your opinion on these things and hope you will take the time to answer. Thank you.

#58 of 65 Re: VSC/TRAC ENGINE LIGHTS [acco20] by wwest

Jan 24, 2012 (5:20 pm)

Replying to: acco20 (Jan 24, 2012 11:01 am)
Yes, disconnect the MAF/IAT sensor module with the engine idling. The engine will stop, reconnect the module, and now for the next few drive cycles you have disabled Trac and VSC, but not ABS.

#59 of 65 Re: VSC/TRAC ENGINE LIGHTS [wwest] by ridgerunner835

Jan 24, 2012 (7:22 pm)

Replying to: wwest (Jan 23, 2012 10:45 am)
We are still watching this,so far the CEL has not come back on....thanks for the tip wwest,if it happens again i will sure be checking this.

#60 of 65 Re: VSC/TRAC ENGINE LIGHTS [wwest] by acco20

Jan 25, 2012 (12:17 pm)

Replying to: wwest (Jan 24, 2012 5:20 pm)
wwest....Thank you for the information. I do not know what the MAF/IAT sensor module is or where it is located. Is this something that can be done if caught in a snowy situation where spinning the tire would be helpful? Can it be done quickly etc. Thanks for any further help you can provide. Also, if I can find it and use the disconnect, will it reactvate on its own after a few drive cycles, and will I know it has reactivated. Hope this is not to much to ask...Thanks.

#61 of 65 Refering to post #60 by acco20

Feb 03, 2012 (11:54 am)

In reference to last post #60.....Can anyone answer these questions? Thank you.

#62 of 65 Re: Refering to post #60 [acco20] by wwest

Feb 03, 2012 (12:21 pm)

Replying to: acco20 (Feb 03, 2012 11:54 am)
MAF/IAT sensor module is always located in the engine intake ducting slightly downstream, after, the engine air filter. And yes, after a few drive cycles it will restore to normal operation.
 
Personally I wouldn't hesitate getting out and going through the procedure should I encounter road conditions that warranted such.

#63 of 65 Re: Refering to post #60 [wwest] by acco20

Feb 05, 2012 (8:30 am)

Replying to: wwest (Feb 03, 2012 12:21 pm)
wwest, Thank you. Very helpful.

#64 of 65 Re: Refering to post #60 [acco20] by wwest

Feb 05, 2012 (10:37 am)

Replying to: acco20 (Feb 05, 2012 8:30 am)
Next time stay away from FWD or even F/awd...except for maybe the SH-AWD system.

Messages Page 7 of 7

To POST a message, please Sign In.

Advertisement

Browse by Category

Browse by Vehicle
   View All Vehicles

Browse by Board
Browse by Topic
View All Topics

Edmunds Community

Advertisement