Last post on Jun 25, 2013 at 7:07 PM
You are in the Chevrolet S-10 & GMC S15 Sonoma
What is this discussion about?
Chevrolet S-10, Auto Repair, Truck
#45 of 95 Re: 1998 s-10 pu wiring troubles [dkeller1]
Sep 23, 2007 (7:10 am)
You need to find a better mechanic.
#46 of 95 Re: 1998 s-10 pu wiring troubles [gonogo]
Nov 14, 2007 (3:31 am)
Get a video Camera, Set it up at the bottom of the canyon.
Get back in the truck, and go flat out full throttle over the cliff.
1] You make more money in one day than you did all your life from the video.
#47 of 95 S10 service engine soon light
Dec 05, 2007 (1:51 pm)
I have a 2001 V6 S10. The service light soon light just turned on, so I went and got it checked. It had a couple of numbers come up, with one being 1860. Pretty much they the service guy told me it was either the ignition or the solenoid. THe next possible problem could be the valve body switch. I was wondering if anybody else experienced this and what the cost was?
#48 of 95 Chevy S-10 1999 4.3L P0300 Code
Jan 07, 2008 (7:20 pm)
Ok so this morning I was on my way to work NO PROBLEMS... stopped for gas(shut the truck off)... filled the tank... went to start the truck.. and thats when the problem started... check engine light... (flashing random pattern) and rough idle as well as running.. went to Advanced auto after work and had them read the computer P0300 code (Multi-Cylinder Misfire) so picked up plugs and wires... (Bosch Platinum 2s and Autolite Professional) and changed them all out (record time too, 2 hrs) anyways still have the problem... any help?
#49 of 95 Re: Chevy S-10 1999 4.3L P0300 Code [djcrzysounds]
Jan 12, 2008 (9:46 am)
Sounds like a cap/rotor failure or fuel pressure issue. Remove the dist. cap and check for watermarks, wear, or carbon tracking. Replace them if you see a problem. also if your fuel filter has not been changed it would be a good idea, being significantly less than a fuel pump. Bosch and Autolite SUCK in GM ignition systems, so replace with ACDelco unless you like changing parts often. You really get whatyou pay for in ignition (and any other electrical) parts.
Hope this helps, and its not a dirty injector or valvetrain issue
#50 of 95 Chevy S10 code PO147
Feb 14, 2008 (11:48 am)
I'm trying to find out what a Code PO147 HO2S Heater Performance Bank 1 Sensor 3 code applies to. This is on a 99 Chevy S10. Do you know?
#51 of 95 1995 S-10 replace OBD I with OBD II
Apr 13, 2008 (10:30 am)
Can the OBD I computer in a 1995 S-10 be replaced with an OBD II computer?
#52 of 95 Re: 1995 S-10 replace OBD I with OBD II [davewilliamson]
by KCRam@Edmunds HOST
Apr 13, 2008 (3:08 pm)
Most likely not, because the necessary sensors for OBD-II won't all be there.
kcram - Pickups Host
#53 of 95 1996 s-10 2.2 code p1886 mfg specific
May 27, 2008 (6:26 pm)
i can't find what this code is in my chiltons book. can any one help with this code. the reader says that it is manufacturer specific. i got that code, then the engine stalled and noe it will carnk over, but not start at all. i am getting fuel and spark. ready to pull my hair out next.
#54 of 95 1997 gmc sonoma check engine on OBD II won't scan ?
Jun 03, 2008 (7:29 am)
I have a 1997 gmc sonoma 4x4 6 cyl check engine light on and the obd II won't scan. I checked the scanner with another car and it works fine ?