Last post on Apr 05, 2013 at 12:27 PM
You are in the Toyota Tacoma
What is this discussion about?
Toyota Tacoma, Auto Repair, Truck
#63 of 86 Re: 1996 hard start when hot [50pill]
Sep 30, 2010 (1:52 pm)
i have a 95 toyota tacoma with a v6 3.4L in it, i had the same problem where my truck would run fine and as soon as i turned it off and let it sit, it wouldnt turn back on, i took it to a dealer and they told me it was my fuel pump and after it was replaced it still did the same thing, then they found out that the wireing harness under my seat was corroded and it wouldnt turn the fuel pump on after a while. So they re did the wiring to my fuel pump and now the problem has been solved.
#65 of 86 Re: 1995 Tacoma, won't start when hot [nlsteve]
Nov 15, 2010 (6:25 pm)
change the ignition coil but only bay the original from toyota others not work (only DENSO brand)
#66 of 86 Re: 1996 hard start when hot [buffer4294]
Nov 15, 2010 (6:27 pm)
you are the men i did by the original and work perfect
#67 of 86 Re: 1995 Tacoma, won't start when hot [malinoisv7]
Nov 18, 2010 (7:31 am)
I had the same problem. It was the distributer, but you have to purchase a Toyota distributer not an aftermarket. That should take care of your problem. I went thru changing all kinds of parts before I finally figured it out. It has to be a Toyota part!!! It will miss or not run at all. Good Luck!!!
#68 of 86 Re: 1996 Tocoma 2.4L Stalls/Shutsdows After Starting [ric44012]
Dec 16, 2010 (2:18 pm)
I am having the exact same problem. Same codes and everything. Believe it or not I was told the timing chain is stretched and is putting the crank and cams out of phase....I know sounds like bull, but I'm looking for a second opinion...have you tried anything else withany luck?
#69 of 86 Re: 1996 Tocoma Stalls/shutsdows After [ric44012]
Jan 19, 2011 (4:25 pm)
#70 of 86 Re: 1996 Tocoma 2.4L Stalls/Shutsdows After Starting [ric44012]
Jan 19, 2011 (4:30 pm)
change the air flow sensor...you wont be dissapointed..
#71 of 86 Re: 2008 TRD Double cab 4x2 4.0 V6 236HP [hackattack5]
Jan 19, 2011 (4:33 pm)
changed the mass air sensor...you can do it..
#72 of 86 Re: stalls when blower and signal are run in conjunction [wirephr3q]
Mar 07, 2011 (12:42 pm)
Just had the same problem. Rt sig and blower on stalls truck. I have a 99 tacoma. Found that with the blower on only I had 4V at ground of the front right turn sig. When I disconnected the blower, thus taking out the resistors and blower switch the problem would then occur with the rt signal even with the blower switch off. Found that with the blower sw off (blower hooked up) there is a path to ground via the resistor bank so the rt sig would work with the blower off. Anyway I found a broked ground located behind the fuel vapor box. There are 2 ground wires comming out of the harness that goes thru the firewall on the drivers side. Since they are protected by the black box I think some small (mouse) broke one of the wires. I fixed the ground and the problem went away. On my tacoma, starting at the front drivers side, Battery, fuse box, Vapor box. Hope this helps you.