You are here: Forums Pickups Ford Ranger Ford Ranger 4x4 Problems

Ford Ranger 4x4 Problems

121 messages,  Last post on Nov 17, 2009 at 4:16 PM

You are in the Ford Ranger Forum. Your Host is kcram

What is this discussion about? Ford Ranger, Truck

Messages Page 11 of 13 1 ... 7 8 9 10 11 12 13 Prev Next Last

Go To Msg # Search This Discussion

#94 of 121 Re: Confused on 4wd [wiwally] by dper299 Mar 23, 2009 (6:30 am)
Replying to: wiwally (Mar 22, 2009 1:50 pm) To be more specific on my question: How does/is the front diff engauged ? I lifted the whole vehicle in the air, started the truck , put it into 4wd and everything turned with the exception of the wheels. But when I put the vehicle down and locked into 4wd the driveshaft is locked in and turns but the Cvs/front axles can spin free Replies to this message: wiwally (Mar 26, 2009 10:26 pm)
#95 of 121 Re: Confused on 4wd [dper299] by wiwally Mar 26, 2009 (10:26 pm)
Replying to: dper299 (Mar 23, 2009 6:30 am) Sorry took so long...only get my email work (and work the w/e shift!) I worked on an '01 which has Ford's latest setup (cv front axles with no disconnect other than the t-case) My parents had a '94 with auto locking mechanical hubs (still different from yours). You have managed to get a model year with what i would consider (and many, many others!) to be Ford's worst idea! (SORRY, but its true!) Here's what i found on your system: Your hubs are called Pulse Vaccuum Hubs (PVH) and are found on model years '98-'00. Basically vaccuum is supplied to each of the front hubs, which locks them in. They work off a vacuum pump which is supposedly located under your air filter box. Check to make sure it is working; if it appears like its working go on to the vacuum line(s)? that lead to the front axle from the pump and check for any leakage. Next check the front hubs. The locking hubs are the black caps in the center of each from wheel…..they snap on and off..(hard to take off without breaking a few tabs, so be careful)..There are seals on these hubs, one or both may not be holding the vacuum created by the pump. If you have a leak anywhere, the hubs are rendered useless. Best bet is to replace with manual locking hubs or this will be a continuous headache. Search AVM hubs on the net, you’ll be able to find Manual lockouts for it. OR TRY THIS..... FOLLOW THE LINK (copy and paste if you have to)   http://www.therangerstation.com/forums/../Magazine/Apr04/offroad.htm Let me know what you think!
#96 of 121 Re: 4 wheel dash lights say im in 4 wheel but front wheels noy pulling [spyac3] by grumpy77 Apr 14, 2009 (5:03 pm)
Replying to: spyac3 (Jan 02, 2009 4:35 pm) what if 4wd hi works but 4low does not work
#97 of 121 4wd selector switch by grumpy77 Apr 15, 2009 (9:05 am)
goes into 4hi but not 4low is it switch or something else anyone have this problem before Replies to this message: mmcfee2 (Apr 16, 2009 4:58 am) grumpy77 (Apr 16, 2009 9:15 am) ford4xnut (May 22, 2009 5:13 am)
#98 of 121 Re: 4wd selector switch [grumpy77] by mmcfee2 Apr 16, 2009 (4:58 am)
Replying to: grumpy77 (Apr 15, 2009 9:05 am) Mine is a 2001 and has the transfer case motor, no locking hubs.....If yours is the same, the fact that 4 wheel high is working tells me the transfer case motor is fine. That leaves suspision with the 4x4 module. The 4x4 module needs reprogrammed or is bad. It is located under the passenger's side kickplate. You can replace it yourself, if you can find one, but you probably don't have the equipment to reprogram it. Replies to this message: grumpy77 (Apr 16, 2009 9:15 am)
#99 of 121 Re: 4wd selector switch [mmcfee2] by grumpy77 Apr 16, 2009 (9:15 am)
Replying to: mmcfee2 (Apr 16, 2009 4:58 am) thanx for the info i hear ford makes one that is already programmed is that true?
#100 of 121 Re: Auto locking hubs [cessna180] by fordsucks01 Apr 21, 2009 (9:32 pm)
Replying to: cessna180 (Jun 02, 2008 5:18 pm) Have 1998 4x4 with vacume hubs. Cant find the tool to take them off. What a really bad design. Vacume hoses need replaced and if there broke your heater takes a crap to. Wheel bearing went bad and melted the hub. Can anyone tell me where to get the hub puller for these hubs. Replies to this message: mjumper (May 03, 2009 6:49 am)
#101 of 121 2001 ford ranger 4x4 stuck in low by mjumper May 03, 2009 (6:30 am)
I switched into 4x4 low yesterday and it won't release. Any suggestions ?
#102 of 121 Re: 2001 ford ranger 4x4 stuck by mjumper May 03, 2009 (6:49 am)
Replying to: fordsucks01 (Apr 21, 2009 9:32 pm) I saw all of the postings about the 4x4 and removing the fuse, did not work. The light on the dash does not go out and it is locked in low 4x4. Any suggestions ?
#103 of 121 1990 ranger over heating in the beach sand by putnumranger May 14, 2009 (7:19 pm)
I have 90 model ranger that runs fine on the highway, but as soon as you hit the beach sand the temp gauge starts to climb. I have flushed the cooling system, I have even removed the thermostat. It helped some, I was able to get down the beach a little bit more before it boiled over.

Messages Page 11 of 13 1 ... 7 8 9 10 11 12 13 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Pickups Ford Ranger Ford Ranger 4x4 Problems