You are here: Forums Pickups Ford Ranger Ford Ranger 4x4 Problems

Ford Ranger 4x4 Problems

120 messages,  Last post on Oct 26, 2009 at 7:44 PM

You are in the Ford Ranger Forum. Your Host is kcram

What is this discussion about? Ford Ranger, Truck

Messages Page 10 of 13 1 ... 7 8 9 10 11 12 13 Prev Next Last

Go To Msg # Search This Discussion

#85 of 120 need help by fomocobro1 Jan 01, 2009 (11:03 pm)
okay my 93 ranger manual t/c 5 speed just died when i was coming home...it felt like the clutch went..so i pulled over and i noticed smoke coming from the bell housing..then i tried to get it to go again and when i got the clutch in it dont make the noise..when i release the clutch either in neutral or in gear it makes a rough noise comin from the bell housing i believe! would this be the transfer case tranny or clutch..as it only makes noise when released in gear or in neutral..but dont make any when engaged..it tries to move then it slips and makes that noise like somethin not metal slapping around in somethin..as i said there was prominenet clutch material smell..im used to the rigs ya could see through the bell housing! Replies to this message: wiwally (Jan 03, 2009 5:20 pm)
#86 of 120 Re: 4 wheel dash lights say im in 4 wheel but front wheels noy pulling [shawnranger99] by spyac3 Jan 02, 2009 (4:35 pm)
Replying to: shawnranger99 (Jan 01, 2009 8:49 pm) After much of my own searching I found the answers if your switch is activating the shift motor on the transfer case. Take off the shift motor and mark the position of the trianular bushing turn the switch to 4 hi and see if the busing moved. Yes in 4 wheel low you can tell it has engaged into low however the 4 wheel still does not work. If you dont want to spend the $150 for manual hubs try this I did it to my 99 Ranger in 2007 and it really works no more problem.    http://www.therangerstation.com/Magazine/Apr04/offroad.htm Replies to this message: shawnranger99 (Jan 03, 2009 5:09 pm) spyac3 (Jan 03, 2009 6:14 pm) grumpy77 (Apr 14, 2009 5:03 pm)
#87 of 120 Re: 4 wheel dash lights say im in 4 wheel but front wheels noy pulling [spyac3] by shawnranger99 Jan 03, 2009 (5:09 pm)
Replying to: spyac3 (Jan 02, 2009 4:35 pm) i purchesed a set of rugged ridge manual locking hubs. I was woundering if they will go into my ranger like a set of avm hubs. the address of the hubs on the net will be at the end of this messege, please take a look at them and tell me what you think. I was woundering how to inststall these myself and how hard it will be? When i put them into place do i put them in set in the locked position?   http://www.speedycarparts.com/sku/Ford_Ranger_Rugged-Ridge_Locking-Hub_1999_2001- _15001.7.html?srccode=cii_9324560&cpncode=17-25758297-2 Replies to this message: spyac3 (Jan 03, 2009 6:14 pm)
#88 of 120 Re: need help [fomocobro1] by wiwally Jan 03, 2009 (5:20 pm)
Replying to: fomocobro1 (Jan 01, 2009 11:03 pm) Sounds like ur clutch went out, but i would check the trans (jack up rear wheels, have someone hold the clutch released and turn the trans output shaft by hand) this will at least let you know the driveline and trans turn freely, and there was no problems there attributing to the clutch failure. if everything sounds fine, then the noise you are hearing is most likely the clutch itself. there should be some sort of access hole or plate to remove to take a peek inside. One things for sure, if you can smell the clutch....it needs a new one!
#89 of 120 01 ranger, 4x4 inop (GO FIGURE!) by wiwally Jan 03, 2009 (5:32 pm)
ok, here comes the age-old deal with these.... 01 ranger, cv front shafts (no lockouts) only 4x4 engage/disengage is the t-case motor. here's whats going on: Start the truck, both 4x4 indicators come on momentarily, then go out. no response from the switch at all, no indicators come on when switched to 4hi or 4lo. fuse in dash good for 4x4, as is 20amp under the hood. checked for power at motor-nothing in any switch position. removed motor, supplied power, works in both directions with no trouble. Disconnected battery to power down and "reset" the 4x4 module.....still nothing. anyone have any wiring diagrams on how this system works? I'm wondering if the sensor/contac ring on the motor is bad, but need to know how to check it. Hate to buy either a motor or a module and not be able to return them! any help greatly appreciated!
#90 of 120 Re: 4 wheel dash lights say im in 4 wheel but front wheels noy pulling [shawnranger99] by spyac3 Jan 03, 2009 (6:14 pm)
Replying to: shawnranger99 (Jan 03, 2009 5:09 pm) I would say if you have mechanical ablility they shouldn't be difficult to install, once they are in if you leave them in the locked position it would be no different then the previous fix i mentioned previously with the website link I provided showing how to bypass the Pulse vacuum system which is basically how the newer models function.   You only need to lock them in when you want 4x4 and you will still need to use the switch on the dash to engage 4 wheel hi and 4 wheel lo.
#91 of 120 4x4 locking in and out while using it. by 2006ranger Jan 17, 2009 (8:05 am)
hi i have a 2006 ford ranger supercab 4x4. i had a problem with my four wheel drive locking in and out when using it in the snow. i took the truck to the local dealer and they told me that one tire was wore down more than the rest and there is a sensor that picks up that tire and it sends a signal to the computer telling it that the onetire is spinning more than the rest or that it is stuck so there for it causes your four wheel drive to not work properly. the only way to fix the problem, is when you need a tire or tireson your truck, its a must to replace all 4 tires or you will have this problem. this is not a bulshit lie, i have tested it with used tires from tire shops and i had all different tires all the way around the truck and the 4x4 locked in and out, but when i put a new set of tires on it stopped.
#92 of 120 Confused on 4wd by dper299 Mar 22, 2009 (10:06 am)
I have a 98 Ranger 4x4 143,000 miles and I thought I had a good idea on how the 4x4 works, but now I am starting to doubt myself.. I know that when you shift it into 4x4 the transfer case motor engauges the transfer case, which in turn locks the front drive shaft.. Now here is were I am lost, The front shaft is locked in,but I can still turn the CV's and the wheels spin free when holding the CV's. I have vacume to the Hub's. Now do the hub's have anything to do with the Front diff locking in and powering the front wheels,or should the front diff be locked in and the (CV's can't spin) with the front shaft when in 4wd. Replies to this message: wiwally (Mar 22, 2009 1:50 pm) dper299 (Mar 23, 2009 6:30 am) wiwally (Mar 26, 2009 10:26 pm)
#93 of 120 Re: Confused on 4wd [dper299] by wiwally Mar 22, 2009 (1:50 pm)
Replying to: dper299 (Mar 22, 2009 10:06 am) You are both right (and wrong) When you activate the 4x4, YES the actuator turns the tcase motor to lock tcase in 4x4. But that actuator is not responsible for locking your front hubs. Your front hubs are locked in via vaccum created by your engine. My ranger is an '01 wich has a different setup (no more vaccum hubs, becasue Ford finally realized they were nothing but trouble!) Your Ranger should have a rubber vaccum line coming down from the engine compartent to provide vaccum to the hubs. check this line for cracking/chaffing. what would be the best would be to manually put vaccum to the hubs and see if they lock. I don't know all the specifics, but i do know a certain amount locks and another amount unlocks them. i don't know where the lines connect exactly either... but your problem lays in the front hubs not locking. When i was looking for info on my '01 not engaging 4x4 i found all kinds of info for your model year....keep looking you'll find the specifics Replies to this message: dper299 (Mar 23, 2009 6:30 am) wiwally (Mar 26, 2009 10:26 pm)
#94 of 120 Re: Confused on 4wd [wiwally] by dper299 Mar 23, 2009 (6:30 am)
Replying to: wiwally (Mar 22, 2009 1:50 pm) To be more specific on my question: How does/is the front diff engauged ? I lifted the whole vehicle in the air, started the truck , put it into 4wd and everything turned with the exception of the wheels. But when I put the vehicle down and locked into 4wd the driveshaft is locked in and turns but the Cvs/front axles can spin free Replies to this message: wiwally (Mar 26, 2009 10:26 pm)

Messages Page 10 of 13 1 ... 7 8 9 10 11 12 13 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Pickups Ford Ranger Ford Ranger 4x4 Problems