You are here:
Forums
Pickups
Ford Ranger
Ford Ranger 4x4 Problems

123 messages, Last post on Nov 30, 2009 at 2:18 PM
You are in the Ford Ranger Forum. Your Host is kcram
| i have a 97' ford ranger. the electronc swich engages the tranfercase, i can feel it go to 4x4 low, the hubs dont lock in. the fuses are good. what can it be? i was thinking the vacume lines? | |
| i have a 97' ford ranger. the electronc swich engages the tranfercase but does not go to the axle and the hubs dont lock in. the fuses are good. what can it be? i was thinking the vacume lines? | |
|
Replying to: jtv3 (Sep 17, 2008 3:27 am) |
|
| i have a 1988 ford ranger xlt 4x4 that has the touch drive 4 wheel drive well i used the 4 wheel drive today in low range and then when i got back onto the road i tried to turn it off and it won't disengage it is stuck in 4x4 low range so far i have pounded on the cylonoid and i have disconnected the battery to try and disengage it and nothing has worked any ideas of how to get it out of 4 wheel drive would be appreciated thanks | |
|
Hello,I put manual hub on a 1997 ranger last year. Now it will not go into 4 wheel drive(hi or lo).The lights on the dash light up when it is started,they work when you turn the switch from 2 wheel drive to 4 hi and lo,but the eletric shift motor doesn't turn. I installed a new electric shift motor,but it doesn't do anything either.There was a wire from the transfer case to the old shift motor.I stripped the wire on the plug going up thru the floor (black I think) and still nothing. What else can I try now. Thanks for any help. |
|
|
Hello,I put manual hubs on a 1997 ranger last year,it worked fine then. Now it will not go into 4 wheel drive(hi or lo).The lights on the dash light up when it is started,they work when you turn the switch from 2 wheel drive to 4 hi and lo,but the eletric shift motor doesn't turn. I checked the fuses in the cab and under the hood,all looked fine. I installed a new electric shift motor,but it doesn't do anything either.There was a wire from the transfer case to the old shift motor.I stripped the wire on the plug going up thru the floor (black I think) and connect the wire from the transfer case to it,still nothing. What else can I try now? Thanks for any help. |
|
my 4x4 traction repeatedly disengages ! winter 2007,ford dealer blamed my lighter [gunked-up w/ashes] on blowing my shared fuse for 4x4...cost me $120, to which ford refuses to reimburse ! ** I ARGUED THAT IT WAS A MAJOR DESIGN FLAW , & FUSE SHOULD BE DEDICATED. fast forward december to 5th 2008,4x4 disengages once again.lighter cannot be blamed because i removed lighter stick after first incident. i purchased truck brand new, & i've used 4x4 lightly [no off-roading] maybe 10x. this is a recall waiting to happen !!
|
|
|
Replying to: red100 (Dec 05, 2008 10:31 pm) thanks! |
|
|
Hi, my son has a 2003 Ford Ranger. The other day it was an icy glaze when he drove it home and parked it in the garage, and he had it in 4 wheel drive. I think he disengaged it at the last minute, but anyway, this AM he tried to back it out of the garage and the rear wheels didn't want to turn, it was like they were locked up. I let him take my car to work. What does he need to do next when he gets home later to make it work again? thank you.... |
|
You are here:
Forums
Pickups
Ford Ranger
Ford Ranger 4x4 Problems
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2010 Ford Ranger



Browse by Board
Browse by Topic
Today's Chats