You are here: Forums Pickups Ford Ranger Ford Ranger 4x4 Problems

Ford Ranger 4x4 Problems

122 messages,  Last post on Nov 22, 2009 at 12:15 PM

You are in the Ford Ranger Forum. Your Host is kcram

What is this discussion about? Ford Ranger, Truck

Messages Page 8 of 13 1 ... 5 6 7 8 9 10 11 ... 13 Prev Next Last

Go To Msg # Search This Discussion

#63 of 122 Flashing 4x4 Dash lights by dper299 Sep 08, 2008 (10:43 pm)
Recentely I tried to shift my 98ranger into 4 wheel drive and nothing happened. Now both 4 wheel high/4 wheel low indicator lights flash together for a few secs then go off for a few mins then flash again. I just changed the transfer case fluid,but this time I used the Merc5 instead of regular ATF,I looked at all the fuses and everything seems ok,Any Ideas? Thanks Replies to this message: dper299 (Oct 07, 2008 5:29 am)
#64 of 122 2001 3L 4x4 won't go into 4 wheel drive by jtv3 Sep 17, 2008 (3:27 am)
I have a 2001 Edge that won't go into 4 wheel high or low. It's done this before while trouble shooting it I found that when I pulled the fuse and put it back in it started to work. It's not working now, any thoughts or suggestions as to what to look at. Thanks Jim Replies to this message: mmcfee2 (Nov 18, 2008 5:43 am)
#65 of 122 Re: Flashing 4x4 Dash lights [dper299]/FIXED by dper299 Oct 07, 2008 (5:29 am)
Replying to: dper299 (Sep 08, 2008 10:43 pm) Hello all: Well I got the above problem fixed. After Taking off the shift motor and taking it apart I found out that the Electric motor had water leak into it from the "O" ring between the motor and gear housing,Thus causing the armature and magnets to rust together,siezing it up.So after getting it apart and getting all the rust off and getting it all cleaned up then applying some waterproof marine grease to the unit,and then sealing with RTV high temp black silicone adhesive where the housing come together.along with sealing any place that might leak inside and out,I put the motor back on the truck and it works as good as new now.
#66 of 122 Hub Assembly by wwheeler15 Oct 10, 2008 (6:42 pm)
I have a 1999 Ford ranger 4x4 with a 5.0. I'm trying to replace the front wheel hub assembly. I took the "nub" off the wheel, It has gears and stuff in it, and i broke the plastic pieces that were holding it on. What is this piece called, and were can i find a new one if i need it?
#67 of 122 4X4 Problems by bullit7 Nov 04, 2008 (8:22 am)
I just bought a 1993 Ranger and the 4 wheel drive doesn't work.Has anyone changed one to manual shift and can it be done.Is it possible to make a shifter to take the place of the electric motor and shift it with a stick?
#68 of 122 '01 4wd problem by el_mn Nov 10, 2008 (9:14 pm)
I have a 01 4 liter automatic. I just took it out of storage a couple weeks ago (stored for the summer) and learned the hard way my 4wd isn't working. I turn the switch and nothing happens... no light comes on, no click in my dash. Possible bad switch or relay??? Checked all the fuses and they were all good. More crap weather is coming this week. Any help would be greatly appreciated. Replies to this message: kevin97116 (Nov 11, 2008 11:31 am) brucelinc (Nov 11, 2008 2:13 pm) el_mn (Nov 12, 2008 2:08 pm)
#69 of 122 Re: '01 4wd problem by kevin97116 Nov 11, 2008 (11:31 am)
Replying to: el_mn (Nov 10, 2008 9:14 pm) When I was having 4x4 shifting issues and was looking for possible fixes (mine ended up being electric hubs, replaced with manuals) I was told that it's common to have the shifting mechanism seize up from grit etc, especially when not used for a period of time. I was told to shift into 4x4 and back out every month of so just to keep the stuff sliding properly. I never ended up having to take my transfer case apart so I can't help much there, but perhaps someone else can tell you what to look for there.   good luck, Kevin
#70 of 122 Re: '01 4wd problem [el_mn] by brucelinc Nov 11, 2008 (2:13 pm)
Replying to: el_mn (Nov 10, 2008 9:14 pm) The 4X4 control module is a pretty common problem on these. Do a search for "Ranger 4X4 control module" and you will find lots of information.
#71 of 122 Re: '01 4wd problem [el_mn] by el_mn Nov 12, 2008 (2:08 pm)
Replying to: el_mn (Nov 10, 2008 9:14 pm) Thanks a ton for all the help guys. I'm pretty positive it's the control module. After doing more research it said they are notorious for going out on 01-03 ford models, especially when you charge or replace the battery. What did i do right before i took it out of storage, had to jump the battery then replace it with a new one... so it must have fried it. My mechanic buddy came over with his plug in computer and the control module was the only thing he couldn't communicate with, so I'm pretty sure that's it. Thanks again you guys saved me a bunch of money on labor fees.
#72 of 122 4x4 not engageing by ranger4x4 Nov 16, 2008 (11:42 am)
i have a 97' ford ranger. the electronc swich engages the tranfercase but does not go to the axle and the hubs dont lock in. the fuses are good. what can it be? i was thinking the vacume lines?

Messages Page 8 of 13 1 ... 5 6 7 8 9 10 11 ... 13 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Pickups Ford Ranger Ford Ranger 4x4 Problems