Sign In Join 



Nissan Quest Brakes

85 messages,  Last post on Dec 04, 2009 at 3:00 PM

You are in the Nissan Quest Forum. Your Host is Karens

What is this discussion about? Nissan Quest, Brakes, Van


Messages Page 9 of 10
1
...
4
5
6
7
8
9
10
Prev
Next
Last
Go To Msg #
Search This Discussion

#74 of 85
Re: want to try doing it myself [tjshan] by cirruss
Aug 04, 2009 (8:41 am)
Reply

Replying to: tjshan (Aug 04, 2009 8:08 am)

Just to let you know, my Frozen rotors warped after about 15,000 miles. They were expensive and not worth the money. I replaced them with all Raybestos rotors and ceramic pads. Not saying these new ones won't warp, but at half the cost, it's easier to swallow. The Raybestos rotors are still smooth after about 6000 miles. If you are doing the work yourself, check out the online store rockauto. I have used them for about 8 years and great price and excellent service.
 
There is a caliper bracket that holds the rotor in. You will definitely need an impact wrench to take the bolts off this bracket. If you don't have one, go borrow one. The brake job itself is same as any other disc brake job - not any harder.
#75 of 85
Re: want to try doing it myself [cirruss] by deltheking
Aug 04, 2009 (4:49 pm)
Reply

Replying to: cirruss (Aug 04, 2009 8:41 am)

Frozen rotors have supposedly a lifetime warranty which they dont advertise. It seems they support their product and stand behind it and they would replace them if they warp that soon.Did u contact them about this?
I have an 04 Quest with OEM rotors and when it`s time to change,I want to use better ones rather than the crappy OEM`s.How are the raysbestos rotors and pads?Might give them a try if they are half the price of Frozen.
Really,the Quest rotors are crappy.
#76 of 85
Re: want to try doing it myself [deltheking] by dtownfb
Aug 05, 2009 (8:52 am)
Reply

Replying to: deltheking (Aug 04, 2009 4:49 pm)

We just had the rear brakes and pads replaced on our 2004 Quest. Our mechanic used NAPA parts. Honestly, I'm not sure any rotor will hold up any better. Nissan did a piss poor job with sizing the brakes for this vehicle esp. the 2004 models.
#77 of 85
Re: want to try doing it myself [dtownfb] by deltheking
Aug 05, 2009 (4:22 pm)
Reply

Replying to: dtownfb (Aug 05, 2009 8:52 am)

Also, do you have the well documented steering wheel shimmy/shake/vibration??The rotors and pads were replaced and it still shakes.Probably a tire balance problem.
Did u have any similar shimmy problems?If yes,what was the solution?
Thanks.
#78 of 85
Re: want to try doing it myself [deltheking] by dtownfb
Aug 06, 2009 (12:07 pm)
Reply

Replying to: deltheking (Aug 05, 2009 4:22 pm)

Now that you mentioned this......
 
I think I found the source of my steering wheel shimmy.....lower control arm bushings.
 
I spoke with my mechanic today because I was having issues. he mentioned that during my inspection (end of June), there was some play in the bushings. he shared with me that he couldn't get the bushings through his normal local supply and tried calling the local Nissan dealership. They only sell the entire control arm which costs $$$$. he balked at this and told me if I can find just the bushings on the internet, he would install it for me. I saw that Rockauto.com sells them for $18: http://www.rockauto.com/catalog/raframecatalog.php
 
This will definitely cure the "thuds" I feel when going over bumps and hopefully the shimmys as well. i tried balancing the tires and while one did need an additional weight, it didn't change much. i would also check the alignment as well. This minivan has a long wheelbase.
#79 of 85
Re: want to try doing it myself [dtownfb] by dtownfb
Aug 06, 2009 (7:00 pm)
Reply

Replying to: dtownfb (Aug 06, 2009 12:07 pm)

Looks like those bushings at Rockauto are for the rear. Checking a couple websites that claim you can replace just the bushings to see where to locate the parts. Will post my findings.
#80 of 85
Re: want to try doing it myself [deltheking] by tjshan
Aug 09, 2009 (8:35 am)
Reply

Replying to: deltheking (Aug 05, 2009 4:22 pm)

Yes, since about 5K miles we have battles the shimmy shake. like i said, 6 sets of brakes, two calipers (hanging up) new tires...the works. about 6k miles ago we had the yoko's put on and at the same time replaced the front drivers caliper (second time) and supposedly new rotors (I never trust the dealer to be honest) and the car rode great, about 1K miles ago we rotated the tires and I began to feel a shake again...ahh...thought I figured it out...had the tires rebalanced (they were off a bit) bit shake still there...in fact worse...I now suspect the rotors. We are going on a long trip next weekend and was going to try to change them myself befor we went. thats why i was looking for the advise.
 
Tom
#81 of 85
Re: want to try doing it myself [dtownfb] by dtownfb
Aug 09, 2009 (9:43 am)
Reply

Replying to: dtownfb (Aug 06, 2009 7:00 pm)

It looks like the bushings in the front control arm are NOT serviceable on the 2004+ Quest. You have to replace the entire control arm. I'll order the control arm tonight and have it installed next week and report the results.
#82 of 85
wrong section by 02quest
Oct 08, 2009 (7:56 pm)
Reply
#83 of 85
brakes on my 07 Quest by ihateminivans
Nov 11, 2009 (7:24 am)
Reply
I was at one point the biggest fan of nissan but up until this latest issue, I have come to the conclusion that Nissan product have a lot to be desired. I currently have an 07 Quest that I lease and let me tell you that once you cross that 30k point, the mini-van will literally fall apart in you hand if not in your driveway. First it started with both sliding doors then it was the strange noise from the undercarriage and last but not least, the brakes.
The brakes are the hardest thing to have a dealer fix and I don't know why. This was my first mini-van that I leased brand new and I hoped that it would last alot longer than it has with out issues. i have already spent easily over $1200 in supposed repairs to the brakes only to have the problem of shaking and rattling come right back within days of picking the van up. The only answer i have been getting from the dealer is that I need to replace more that just the brake rotors and pads but now it could be the tires or the rims themselves. ultimately after doing all that was recommended, the van still has the original problem of shaking and rattling when you apply the brakes after being being used once or twice.
So I started doing my own research and i am a little bit of a shade tree mechanic, so what i found out was that if i went out and purchased a performance rotors that are slotted for both the front and back. That would stop the problem of the shakes that comes from the small size of the original rotors and not being able to the heat that is created from the use. quoted price of after market performance rotor front and back $180 with tax.. amount already spent $1200. I think the choice is obvious. I'll will update when i'm done with the upgrade and the overall results.

Messages Page 9 of 10
1
...
4
5
6
7
8
9
10
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics

Today's Chats

Advertisement