You are here: Forums Sedans Mazda 626 Mazda 626 Engine Questions

Mazda 626 Engine Questions

29 messages,  Last post on Aug 21, 2009 at 11:02 AM

You are in the Mazda 626 Forum. Your Hosts are pat & karens

What is this discussion about? Mazda 626, Sedan

Messages Page 3 of 4 1 2 3 4 Prev Next Last

Go To Msg # Search This Discussion

#17 of 29 2002 Mazda 626 Engine warning light by rezans Jul 11, 2008 (2:18 pm)
My engine warning light just showed up for the first time on my 2002 Mazda 626. I have 68000 miles on it. Does anyone know what this light indicates? I looked at my owner's manual and it states it could be low fuel which I know my tank is full. or the gas cap is loose which it is not or there is something wrong with the engine and should be taken to the nearest dealership for service. But before I do so, I want to hear advice from other owners out there. Your help is most appreciate. Thank you! Replies to this message: sylviabob (Jul 30, 2008 6:22 pm) rezans (Jul 30, 2008 8:35 pm)
#18 of 29 96Mazda 626 by peggypeg12 Jul 26, 2008 (1:33 pm)
Yes,if someone can help me,my car ODO LIGHT keeps coming on when the car gets hot,can someone tell me what the problem with my car is? is it the malgalator? please let me know,and my engiine light is coming on,they tested it and said it might be my catalit converter,can some one out there please tell me what is wrong with my car.
#19 of 29 Re: 99 mazda 626 overheated and wont start [sharkpimp] by roman9vs10 Jul 27, 2008 (7:21 pm)
Replying to: sharkpimp (Mar 24, 2008 2:38 pm) I first read about your car problem today, Did you find your problem?
#20 of 29 Re: 2002 Mazda 626 Engine warning light [rezans] by sylviabob Jul 30, 2008 (6:22 pm)
Replying to: rezans (Jul 11, 2008 2:18 pm) this happened to me several times; even though it seems like the gas cap is tight; it wasn't ... tighten it and drive the car for awhile... my light did go off Replies to this message: rezans (Jul 30, 2008 8:35 pm)
#21 of 29 Re: 2002 Mazda 626 Engine warning light [sylviabob] by rezans Jul 30, 2008 (8:35 pm)
Replying to: sylviabob (Jul 30, 2008 6:22 pm) thanks so much! it worked!
#22 of 29 Alternator replacement by ken1964 Oct 02, 2008 (6:12 pm)
I recently purchased a 1989 Mazda 626 from a friend. It needs a new alternator. I haven't been under the hood, so I don't know the engine layout yet. How difficult is it to change and where on the engine is it located?
#23 of 29 Crank Pully replacment by derwin1 Oct 11, 2008 (3:47 pm)
I have a 1993 626 and it chews up the water pump/alternator belt often. The crank pulley is out of alignment with the alternator & water pump. This is a two piece crank pulley that has an outer ring the belts ride in attached to an inner hub that fits on the crank shaft. The outer ring has moved foward about 1/4", I can't get the bolt off the pulley because the crank shaft turns when I try to loosen it. How do I get the bolt off? Please help!! Replies to this message: lmgeary (Jun 14, 2009 3:09 pm)
#24 of 29 Re: Ticking in or by the valves [fordlover100] by rallen210 Apr 28, 2009 (1:30 pm)
Replying to: fordlover100 (May 29, 2007 4:18 pm) I have a 1998 Madza 626 ES,2.5,with a V-6, I had the same type of sound on my Madza, I researched and found the timing belt can make this type of sound. Took it to a repair shop and that is what that sound was, like a clicking sound. I had thought is was internal and serious, in a way it was it had cost me $800 a lot of other parts were needed. I is suppose to be done aprox 60000 miles   rallen210verizon.net
#25 of 29 Crank Pulley by lmgeary Jun 14, 2009 (2:59 pm)
I have a 1995 Mazda 626 that the alternator belt makes a squeeling sound and eventually breaks. I'm told the pulley is out of alignment and it has been re-aligned. After a month or so, the squeeling starts and the same thing happens over and over. I've done some research and found that I need a new pulley. Does anyone know anything about this ???? Need to get this problem fixed once and for all.
#26 of 29 Re: Crank Pully replacment [derwin1] by lmgeary Jun 14, 2009 (3:09 pm)
Replying to: derwin1 (Oct 11, 2008 3:47 pm) Did changing the pulley solve your problem of the belts getting chewed up ??? I'm having the same problem and keep bringing it back to the mechanic but it ends never getting resolved. Please let me know.   Thanks

Messages Page 3 of 4 1 2 3 4 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Sedans Mazda 626 Mazda 626 Engine Questions