You are here: Forums Coupes & Convertibles Chrysler Sebring Chrysler Sebring Starting and Stalling Problems

Chrysler Sebring Starting and Stalling Problems

132 messages,  Last post on Nov 15, 2009 at 11:41 AM

You are in the Chrysler Sebring Forum. Your Host is claires

What is this discussion about? Chrysler Sebring

Messages Page 11 of 14 1 ... 8 9 10 11 12 13 14 Prev Next Last

Go To Msg # Search This Discussion

#99 of 132 Re: Problem Starting 99 Sebring jxi conv [jmccafferty] by vampire87 May 21, 2009 (1:33 pm)
Replying to: jmccafferty (Mar 30, 2007 6:56 pm) have you tried programming a new key to your car. they have a bad habit of not recognizing keys.
#100 of 132 Re: My 1999 Crysler Sebring Conv. Wont start [skipford1] by vampire87 May 21, 2009 (2:18 pm)
Replying to: skipford1 (Sep 02, 2007 7:46 am) try programming a new key to your car and replacing the crank shaft position sensor. good luck let me know how it goes
#101 of 132 Chrysler Seabring problems. Please Help by jengary0325 Jun 18, 2009 (4:10 pm)
I have a 1998 Chrysler Sebring that was given to me and it drove fine for about 3 weeks then all of a sudden I was driving down the road and it didn't want to go and tried to stall out. I got it towed to a mechanic who took two days to tell me that it doesn't show up on the diagnostic and it needs a new computer. He wants to charge me $700. The car still starts it just tries to stall when you drive it. It is still at the mechanic but I have other people telling me that the car runs so the computer is fine. Can anyone give me some advice or know what would be wrong with it? Replies to this message: 1997lxi (Jun 18, 2009 6:24 pm) jpf (Jun 19, 2009 2:52 pm)
#102 of 132 Re: Chrysler Seabring problems. Please Help [jengary0325] by 1997lxi Jun 18, 2009 (6:24 pm)
Replying to: jengary0325 (Jun 18, 2009 4:10 pm) I had a 1997 Sebring LXi with similar symptoms. Mechanic replaced the Exhaust Gas Recirculation E.G.R. Valve located directly behind the engine adjacent to the firewall. That corrected the problem and the repair cost about $150. Good luck.
#103 of 132 Re: Chrysler Seabring problems. Please Help [jengary0325] by jpf Jun 19, 2009 (2:52 pm)
Replying to: jengary0325 (Jun 18, 2009 4:10 pm) Sounds like the mechanic doesn't know what the problem is and wants you to throw some money his way. I suggest you take your car to another mechanic; even if you have to pay to have it towed. Good luck.
#104 of 132 sebring stalling out ans\d starting back no problem. by chriscapo Jun 28, 2009 (4:35 pm)
I had a 98 sebring lxi ran great 80k miles. all of sudden at traffic jams or coming to lights it would stall.. sometimes start right back up sometimes take 20 minutes. So i started with new plug, wires, pvc valve, fuel filter, fuel pump, cap rotor and even new distributor. Something told me this aint right still doing the same thing. so i decided to gamble and go buy a cranshaft position censor 64.99 autozone. had a mechanic install after he insisted this would set off the engine light which wasnt going on. long stoy short he did it and its been fine since then..iff u are having this problem please start at the crank shaft position censor. will save u alot of time and money. which I had started here.. good luck and sometimes when the car is not setting off codes mechanics dont know what the problems are without just trying new things which cause u money
#105 of 132 sebring just stalling out!!!!!did everything but this by chriscapo Jun 28, 2009 (4:45 pm)
My car 82,000 miles and all of a sudden at traffic jams or traffic lights it would die. I thought right away needs a tune up. so i installed new wires,plugs, distributor, cap, rotor, fuel filter, pvc valve, fuel pump,battery. bbom day later did the same thing. so i took a gamble went and bought a crankshaft position Censor. installed it and walla!!! car has been running fine. my compuiter was hooked up to 2 different computers to do a code reading and nothing was coming up..so they mechanics told me same thing they dont know what it was.. TRUST ME CHANGE CRANKSHAFT CENSOR Replies to this message: vampire87 (Jun 29, 2009 8:16 am)
#106 of 132 Re: sebring just stalling out!!!!!did everything but this [chriscapo] by vampire87 Jun 29, 2009 (8:16 am)
Replying to: chriscapo (Jun 28, 2009 4:45 pm) your gonna want to replace the map sensor on the manifold 1 min job. and if that don't work id say do replace the speed control sensor on the trany also easy. just remove the front driver side tire and its located on top of the trany in plain sight. good luck and let me know how it goes.
#107 of 132 Re: ERROR CODE P1684 [enfield76] by liverboy58 Jul 26, 2009 (2:24 pm)
Replying to: enfield76 (Mar 04, 2007 2:51 pm) My 98 did that same thing. It would start sometimes and sometimes not for awhile. It was my antitheft relay. On the 98 it has three relays on the firewall and it was the middle one. You can try that. It worked for me.
#108 of 132 03 sebring stalling when stopping by 03ejhsebring Aug 11, 2009 (9:27 am)
03 sebring seems to fun fine, but has been stalling and dying when coming to a stop and then trying to accelerate. will lose all power and need to turn key to off and will restart ok. have cleaned the idle air control valve and replaced throttle position sensor, but is still stalling. mechanic having hard time to duplicate as doesn't always have problem. no error codes on his diagnostic computer. need ideas for next step. thanks Replies to this message: bobmasabny (Aug 11, 2009 10:23 am)

Messages Page 11 of 14 1 ... 8 9 10 11 12 13 14 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Coupes & Convertibles Chrysler Sebring Chrysler Sebring Starting and Stalling Problems