Last post on Dec 10, 2013 at 6:40 PM
You are in the Chrysler Sebring
What is this discussion about?
Go to NHTSA to file a safety complaint.
Or call Monday-Friday (8 am to 8 pm ET) (888) 327-4236 TTY: (800)424-9153
#247 of 271 Re: help please!! we are lost!! [jerseyg1rl]
Feb 07, 2013 (6:09 pm)
Check your fuel pressure
(I'm from Sayreville NJ but living in South Louisiana now...I have a '99 JXI)
#248 of 271 Re: 08 sebring shutting off [wznhnt]
Feb 27, 2013 (6:55 am)
I have just started having the same problem with my 2008 Sebring. Will lose power suddenly, and idiot light comes on. My mechanic has replaced to different items in the last month, after reading codes. Have had it back for 2 days and light came back on this am, loss of power, etc. Love the car , but got it because my old car was strting to nickle and dime us to death. Now don't know what to do, as this one seems to be doing the same thing.
#249 of 271 Re: 08 sebring shutting off [cjmowers]
Feb 28, 2013 (7:42 am)
the 2008 and some 2007's had a electrical recall. I think there are 8 total recalls. But here is the link on 4 of them .. See if yours is part of the recall and if they will repair the car if not save your money and sell it looks at KIA, Honda, Toyota or Ford
Like most car makers they choose a small range of cars using the vin numbers then say Oh your car is not part of the recall in order to save money. If they get caught or sued then they EXPAND the recall like what happened to Honda and Toyota lately. Chrysler used to mean quality uo until the mid 70's when to Cordoba / Aspen model came out then it was just straight down hill!
#250 of 271 1996 Chrysler Sebring Electrical Issues (stalls, lurches, etc.)
Feb 28, 2013 (10:46 am)
I am having stall problems (at stops or while idling and can be immediately started again), along with RPMs revving randomly, and cruise control randomly turning off.
I have replaced multiple parts, including the MAP sensor. Now I have to have an electrical diagnostics in the next few weeks at the Dealer (can't get in any sooner). No recalls on this issue for this year/make. I would recommend anyone with a 1996 or 1997 Sebring with similar issues call Chrysler Customer Service at 800-853-1403 and ask a file be created for your vehicle. They did call the dealer I am working with, so they know I have been in touch with Chrysler. No recalls can happen unless people make these issues known (power to the masses and all that!!). I will be happy to report any solution, but I can tell you I have replaced the timing belt, water pump, fuel pump, spark plugs, fuel filter and have regular oil changes and use additives to reduce water in the gas. And no, I cannot just run out and buy another vehicle...I am all in at this point. Thinking I didn't have this problem any more, I have a new roof on the car...so it LOOKS GREAT...big deal. Again, call and report your issues...it could help all of us with this year and issue.
#251 of 271 Re: 1996 Chrysler Sebring Electrical Issues (stalls, lurches, etc.) [lexihc]
May 04, 2013 (5:44 pm)
I have the same exact problem. By any chance did you find out what the problem was? This sucks. I hope you're not still having the same dangerous problem. I would really appreciate your advise. Thanks man.
#252 of 271 Re: sebring stalling out ans\d starting back no problem. [animalatr]
May 08, 2013 (5:49 pm)
check the fuel you are using,they are picky when they get some miles..if 93 octain don't help,check your throttle body, it might help to clean around the baffle..spray heavy with throttle cleaner after you wipe out. spray with motor running with a little rev...you can also use sea foam through a vaccume line, keep engine revved while doing so...will smoke a lot while doing this, that is normal, allow to run with a rev till smoking stops. let me know if this helps you...it helped mine..
#253 of 271 Re: 1996 Chrysler Sebring Electrical Issues (stalls, lurches, etc.) [lexihc]
May 29, 2013 (12:32 pm)
you may check the engine coolant temperature sensor. it tell computer the temp of motor and the computer uses that info to determine fuel and air etc to give the engine...if it is bad it will not set off engine light but send bad info to computer
ex engine hot sensor says its cold it dumps more gas than needed car stalls etc etc it is a simple fix cheap
it has nothing to do with temp you see on dash totally separate sensor for that ECT is for pcm only
engine coolant temp sensor change it out good luck
#254 of 271 Re: 97 Sebring Conv. Loses power/stalls when accelerating. [dano853]
Jul 09, 2013 (8:27 am)
This may be nothing but my ford ranger had starting issues for about a year ( replaced fuel filter and the pump )sometimes after it warmed up it just wouldn't restart for a few hours then for no rhyme or reason it would start. End result it was my f#$%ing $20 fuel relay. Been running fine ever since.
#255 of 271 Re: 97 Sebring Conv. Loses power/stalls when accelerating. [dano853]
Jul 11, 2013 (9:13 am)
Please tell me you found a solution to this problem. I have been researching this problem for a while and all the solutions point to a $500 fix. I just do not have that kind of money. Now your description of the problem is an exact match to mine. Especially the part about wet weather making the problem really bad. Ive been able to make it through the summer but winter is coming and I can just imagine the crap shoot that will be. So please share with me what you learned.
#256 of 271 Re: 97 Sebring Conv. Loses power/stalls when accelerating. [jklin]
Jul 11, 2013 (11:29 am)
Ok this sounds like it could be the MAF.. Mass Air Flow sensor. Do you have the LX JX V6 or 4?
Problems with Mass Air Flow sensors are common. Bad or contaminated CHRYSLER Sebring Mass Air Flow sensor can possibly cause a wide range of various vehicle drivability problems such as stalling, especially when the engine is cold, misfiring, poor acceleration, etc. In addition, a problem with the Mass Air Flow sensor often causes the "check engine" or "service engine soon" light in the vehicle instrument panel to illuminate.
The Air Flow Sensor or Mass Airflow Sensor (MAF) is one of the components of an electronic fuel injection system and is found in many of modern vehicles. Most mass air flow sensors are one piece hermetically sealed units with no moving components.
The Mass Air Flow sensor is used to measure (actually weight) the amount of air entering the engine. This measurement is used by the engine computer or ECM to calculate proper amount of fuel injected into the cylinders in order to provide optimum combustion and low emissions.
CHRYSLER Sebring Mass air flow sensor requires no regular maintenance. On mass air flow sensors with a sense wire, this wire can become contaminated with dust particles. These particles can be removed with automotive solvents that are safe for the use on mass air flow sensors. CHRYSLER Sebring mass air flow sensors are commonly misdiagnosed. Before replacing the mass air flow sensor check for air leaks in the connecting air ducts and intake manifold. These leaks can cause similar symptoms as a malfunctioning mass air flow sensor.
The CHRYSLER Sebring Mass Air Flow sensor is usually installed in the intake air duct between the air filter and the throttle body mounted on the intake manifold. Some mass air flow sensors are mounted directly to the throttle body.