You are here: Forums Sedans Mazda 626 Mazda 626 Transmission Questions

Mazda 626 Transmission Questions

44 messages,  Last post on Nov 03, 2009 at 1:33 PM

You are in the Mazda 626 Forum. Your Hosts are pat & karens

What is this discussion about? Mazda

Messages Page 5 of 5 1 2 3 4 5 Prev Next Last

Go To Msg # Search This Discussion

#34 of 44 2000 626 transmission by bass_box Dec 12, 2008 (5:43 pm)
Replying to: kfpfla (Sep 12, 2008 8:24 am) i have a mazda 626 es 2000 i drove it to my friends house 1300 miles away from were i lived and the trans. messed up and i ended up drivein 600+ miles on it in 3rd or atleast 400 miles like that till it started to shift agian.... im in middle of replaceing trans.. and my problem is the torch converter dosent line up right... what could be wrong... is it keyed? to were it only lines up a sertian way..need to know befor i return it and try and rebuild my trans.. cuz i dont know how to realy repair it jest how to change parts out...
#35 of 44 Re: 626 slipping [alexmbj] by raphao Jan 03, 2009 (3:03 pm)
Replying to: alexmbj (Nov 27, 2007 1:10 pm) Hi i have the same problem, did you found what was wrong>???   pls replie at, raphaohotmail.com
#36 of 44 [alanbiogen] Did u ever get your engine light off? by mlbscouting Jan 23, 2009 (6:48 am)
Replying to: alanbiogen (Nov 12, 2008 5:06 pm) My 2000 Mazda 626 engine light was on and the gears began to shift differently(slight slipping). I took it to AutoZone for a diagnosis and it came up with the code P0715(Turbine shaft speed sensor). I purchased a sensor and had it installed by a local mechanic. The car then drove perfectly fine. The next day, the engine light was back on as soon as I pulled out of the driveway. The gears also began to slip again. I then took the car to Mazda and they diagnosed the same exact code, but suggested that I may need a new transmission. Is it possible that the sensor that was replaced could have malfunctioned, since it did not come from Mazda? If I put in a sensor from Mazda, will that be the trick? It drove perfectly fine the day that it was replaced. Is there a way to turn out the annoying engine light? Replies to this message: backy (Jan 23, 2009 10:03 am) bt100 (Nov 03, 2009 1:33 pm)
#37 of 44 Re: [alanbiogen] Did u ever get your engine light off? [mlbscouting] by backy Jan 23, 2009 (10:03 am)
Replying to: mlbscouting (Jan 23, 2009 6:48 am) One thing to consider... when I bought my 2000 626 I4 AT a few years ago, it exhibited similar symptoms. The dealer's service manager recommended installing a transmission cooler, said that often took care of the problem. Cost about $200 installed back then. Have not had any transmission problems since then, although the fluid was pretty dark after only about 15k I had put on it so I had the fluid flushed recently. Don't know if that would fix your problem, but you might want to ask about it as an option to a tranny replacement--a lot cheaper!
#38 of 44 1990 626 Transmission by avalanche1962 Feb 22, 2009 (6:48 pm)
My 626 won't turn over but has full electrical power. My first thought was starter or alternator, but when looking the engine over I noticed two wires sticking out of the bottom of the car and one of them was disconnected. They connect to what I think is the transmission pan. It looks similar to a oil temperature sensor except the wires connected to posts on top as if they were molded into the plastic. Could this be some kind of sensor that would prevent the engine from even trying to start?
#39 of 44 1998 626: automatic transmission issue? by galaxy61z Apr 12, 2009 (4:35 pm)
My wife's car; it ran great, reved fine, no mobility, little at first, then none. A transmission line was leaking (the one that takes fluid into the radiator. I replaced that. the car has been parked since july 2006. We got married on July 29th and had other things to do. The car still runs fine and looks good. It will move but only when reved high, and then it only crawls. should I drain the fluid at replace the filter? or... (any suggestions are welcomed). Im sorry to say, she is now deceased.   Thanks
#40 of 44 Turn signal slow to start by ronper Jun 01, 2009 (7:16 pm)
I have a Mazda 626 1993 model 4cyl Auto transmission car.   Since of late, when I want to indicate to turn left or right, it takes a few minutes before it starts to flash. On hot days it flashes OK.   I also find that when the hazard warning is switched on, the indicatoir lights flash normally. Any ideas about this problem?
#41 of 44 Re: trans range switch [alanbiogen] by dante007 Jul 23, 2009 (8:46 pm)
Replying to: alanbiogen (Nov 12, 2008 5:06 pm) hello, i also have the same problem (2000 626 LX). my mazda will shift around 5000 rpms? can i replace the transmission fluid myself? How do i do this? Can anybody give me step by step procedures? I would like to know where is the speed sensor located? have you heard of the transmission fluid type M3? i was told that this needs to be used instead of the regular ATF?   Please help, I AM DESPERATE AS WELL! e mail me dante_merinolive.com with your responses.   Thank you
#42 of 44 Start mixed with auto transmission by jiovany Aug 13, 2009 (4:47 pm)
A few months ago I spent a fortune changing the transmission on my Mazda 626 model 97,I dont really use a lot this car , a few months ago suddenly the car didn't start , so a friend put a wire between the battery and the starter, and the engine turn on like regular , but regardless if you put on P,N,R or D the car only runs on D , and since then this is the only way to turn on and run the car I'm almost sure that is something simple but i dont want to take the risk to pay another fortune, can you help me on getting an idea about what could be possible wrong?   Thanks and please address your answer to Jiovanybulnesyahoo.com
#43 of 44 Re: 97 626 transmission problem [kfpfla] by tazd23 Sep 01, 2009 (7:21 pm)
Replying to: kfpfla (Sep 12, 2008 8:24 am) I have a 2001 mazda 626 and have the trans. cooler on it already and it works great but i just recently put a trans tune product in form autozone and my overdrive light started flashing but it sifts and runs normal. what should i do?

Messages Page 5 of 5 1 2 3 4 5 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Sedans Mazda 626 Mazda 626 Transmission Questions