You are here: Forums Pickups Mazda B-Series Mazda B-Series Engine Problems

Mazda B-Series Engine Problems

58 messages,  Last post on Nov 23, 2009 at 9:52 AM

You are in the Mazda B-Series Forum. Your Host is kcram

What is this discussion about? Mazda B-Series Truck, Engine, Truck

Messages Page 3 of 7 1 2 3 4 5 6 7 Prev Next Last

Go To Msg # Search This Discussion

#15 of 58 Mazda B2500 races sporatically by fraban Aug 23, 2007 (8:46 pm)
Found the problem. I purchased a Throttle Position Sensor located on the back side of the carberator. It cost me $36.99 at an automotive parts supply store. After replacing the old unit a friend used the truck for a week and logged nearly a thousand miles. No more problems!
#16 of 58 Florescent Yellow Fluid Found Under Truck by mzda2000 Aug 29, 2007 (7:21 am)
#17 of 58 Florescent Yellow Fluid Found Under Truck by mzda2000 Aug 29, 2007 (7:21 am)
While washing the passenger side wheel well found some florescent yellow fluid. Any idea where it could be coming from? No puddle found in driveway.
#18 of 58 1987 Mazda B2000 Pickup by 7801brian Nov 11, 2007 (5:15 pm)
I have a 1987 Mazda B2000 pickup with a bad engine. A rebuilt 1990 Mazda 2.2 engine was advertised locally out of a Ford Probe. How difficult or is it even possible to put the Probe engine in my Mazda pickup. They are both manual transmissions.
#19 of 58 Re: Please Stop Messages in replying to; 2001 Mazda B3000 Series P/U, F/C troub [russ52] by zacheria_30 Nov 24, 2007 (4:51 pm)
Replying to: russ52 (Jun 15, 2007 9:07 am) I have the same problem with my pickup my 2001 Mazda B3000, and i can't figure out whats wrong. If you could tell me i would be greatful.
#20 of 58 89 Mazda B-2200 Running Roughly by tdharness Dec 03, 2007 (4:24 pm)
I need some assistance but first time here and not sure where to post. I recently purchased the 89 Mazda B-2200 and having some issues with it. Is seems to really idle roughly and acts as if it has a lot of trouble accelerating. It won't even go over 62 mph and takes forever for it to even reach that speed. I have replaced the distributor, rotor button, spark plugs and wires and hasn't helped. It also gets terrible gas mileage which isn't good since that is the whole reason that I purchased the vehicle to start with. It will hardly crank if it sits for a little while and when it cranks it tends to cut off frequently especially at red light..LOL! Any help of this situation would be greatly appreciated Replies to this message: 7801brian (Dec 05, 2007 6:53 am) allmycars (Dec 24, 2007 12:06 pm) lmoreno3 (Jun 16, 2009 6:41 pm) the_bean (Feb 29, 2008 10:47 am) 7801brian (Dec 31, 2008 6:46 pm)
#21 of 58 Re: 89 Mazda B-2200 Running Roughly [tdharness] by 7801brian Dec 05, 2007 (6:53 am)
Replying to: tdharness (Dec 03, 2007 4:24 pm) I'm not a mechanic but my B2000 had similar symptoms to what your describing.What I eventually found was the key and keyway in the crankshaft that the lower timing belt sprocket is drive by were woren. This caused the timing of the engine to be offf. I'd start by checking the engine timing . If that's correct you can loosen the belts for the fan A.C. ,etc. and check to see if fan pulley can be turned back showing wear in this keyway area .
#22 of 58 Re: 89 Mazda B-2200 Running Roughly [tdharness] by allmycars Dec 24, 2007 (12:06 pm)
Replying to: tdharness (Dec 03, 2007 4:24 pm) try installing a new nikki carb. i did and it runs great now. try ebay. Replies to this message: lmoreno3 (Jun 16, 2009 6:41 pm)
#23 of 58 swapping a b2200 engine with a b2600i by whidbeyrep Feb 22, 2008 (10:37 pm)
I currently have a 88 B2200 truck that i want to install a B2600i engine out of a 92. How much swapping needs to be done? i believe the fuel tank along with the computer and wiring needs to be swapped. I just removed the 2200 engine and would like some advice prior to yanking out the 2600i. I also know the engine mounts are different but should mount up fine. Any advice would be welcome.
#24 of 58 Re: Mazda b2000 [gc3539] by the_bean Feb 29, 2008 (10:38 am)
Replying to: gc3539 (Feb 05, 2007 9:20 am) you can swap any engine! it may just take a little work. with most swaps you normally will have to change the mounts. there are so many issues to look at but the esiest way to do it is to do a complete swap. (engine tranny computer and harness) there are less things you have to build

Messages Page 3 of 7 1 2 3 4 5 6 7 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Pickups Mazda B-Series Mazda B-Series Engine Problems