You are here: Forums Sedans Ford Crown Victoria/Mercury Grand Marquis Ford Crown Victoria/Mercury Grand Marquis Electrical/Lighting

Ford Crown Victoria/Mercury Grand Marquis Electrical/Lighting

122 messages,  Last post on Nov 05, 2009 at 5:55 PM

You are in the Ford Crown Victoria/Mercury Grand Marquis Forum. Your Hosts are pat & karens

What is this discussion about? Ford Crown Victoria, Mercury Grand Marquis, Lights, Electrical, Sedan

Messages Page 13 of 13 1 ... 7 8 9 10 11 12 13 Prev Next Last

Go To Msg # Search This Discussion

#115 of 122 Re: “intermittent” wiper problem [captdan3] by patrock61 Oct 02, 2009 (1:12 pm)
Replying to: captdan3 (Oct 02, 2009 12:31 pm) Thanks for the info what did the wiper motor cost you and how much is intailed in changing it ??? Replies to this message: patrock61 (Oct 10, 2009 7:10 pm)
#116 of 122 Turn Signals on 1997 Grand Marquis by joeohara2 Oct 10, 2009 (4:59 pm)
I have no turn signals on either side but my hazard flashers work fine. I've replaced every bulb front and rear and checked every fuse. Prior to the loss of my turn signals, I heard an audible clicking noise under the dash intermittently for a number of months. I ignored it. I also had a blown bulb on one side so the clicking noise was faster on the left side than the right side. Now I have neither side. From what I've learned either the Lighting Control Module or Multi-function switch is bad. Any help or advice you can provide would be most helpful. Cheers, Joe
#117 of 122 Re: “intermittent” wiper problem [patrock61] by patrock61 Oct 10, 2009 (7:10 pm)
Replying to: patrock61 (Oct 02, 2009 1:12 pm) Update , I changed the motor it was 63 dollars ..Quite the project to change it you have to remove wiper arms . Update , I changed the motor it was 63 dollars ..Quite the project to change it you have to remove wiper arms . Take off both sides of the leaf screen you will need a Phillips screw driver and something to take out the 2 push fasteners on either side . remove inside motor cover remove retainer clip from motor arm remove three bolts securing motor . Remove the 5 or 6 bolts that hold the motor mounting /wiper arm plate lift motor mounting plate unplug motor and remove to install follow this procedure in reverse except motor can be bolted in before mounting plate is rescued . Total time should take you about 2 to 3 hours with 3 busted knuckles.   Problem is solved all wiper function work perfectly now thanks for the advice                                                         Patrick
#118 of 122 CROWN VIC ELECTRIC PROBLEM by scaldog1 Oct 12, 2009 (5:36 pm)
I HAVE A 2000 CROWN VIC, EX POLICE CAR AND AM HAVING SOME ELECTRIC ISSUES. SOMETHING IS DRAINING THE BATTERY, BUT THE BATTERY CHECKED OUT GOOD, NO FUSES ARE MESSED UP, REPLACED WIRING HARNESS TO MOTOR, NO LIGHT BULB IN TRUNK OR UNDER HOOD, BUT BATTERY IS STILL DRAINED LIKE SOMETHING STILL ON. CAN'T FIGURE IT OUT, CAN ANYBODY HELP WITH THIS? THANKS Replies to this message: pmitchellp (Oct 14, 2009 12:59 pm) randalls1 (Nov 05, 2009 5:55 pm)
#119 of 122 grand marquis headlights by sandyihall Oct 14, 2009 (12:44 pm)
My 2004 Grand marquis headlights go out and I can not get them back on I tried all lighting controls but nothing. The bright beams won't stay on either. How can I fix this without a new module? Replies to this message: pmitchellp (Oct 14, 2009 1:01 pm)
#120 of 122 Re: CROWN VIC ELECTRIC PROBLEM [scaldog1] by pmitchellp Oct 14, 2009 (12:59 pm)
Replying to: scaldog1 (Oct 12, 2009 5:36 pm) Your vehicle is maybe six years old now. Have you checked your alternator? They can check it at Auto Zone with their machine. Or you can take it out and bring it up there and they can run it through the tester, which is the best way to tell if it is failing under full load.
#121 of 122 Re: grand marquis headlights [sandyihall] by pmitchellp Oct 14, 2009 (1:01 pm)
Replying to: sandyihall (Oct 14, 2009 12:44 pm) You probably can't.
#122 of 122 Re: CROWN VIC ELECTRIC PROBLEM [scaldog1] by randalls1 Nov 05, 2009 (5:55 pm)
Replying to: scaldog1 (Oct 12, 2009 5:36 pm) We had a similar problem. The Crown Vic would always start and run fine but every 7 days or so the battery would run down. Turned out to be the starter solenoid on the fender well. It was very slowly draining the battery down but still worked okay. When it was replaced the problem went away.

Messages Page 13 of 13 1 ... 7 8 9 10 11 12 13 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Sedans Ford Crown Victoria/Mercury Grand Marquis Ford Crown Victoria/Mercury Grand Marquis Electrical/Lighting