Sign In Join 

You are here: [F] Forums / SUVs / Jeep Wrangler / Jeep Wrangler Tires and Wheels



Jeep Wrangler Tires and Wheels

193 messages,  Last post on Sep 26, 2009 at 5:22 AM

You are in the Jeep Wrangler Forum. Your Hosts are steve_ & tidester

What is this discussion about? Jeep Wrangler, Jeep Wrangler Unlimited, Jeep Scrambler, Jeep CJ-5, Jeep CJ-7, Tires, Wheels, SUV


Messages Page 16 of 20
1
...
13
14
15
16
17
18
19
20
Prev
Next
Last
Go To Msg #
Search This Discussion

#150 of 193
Re: rear transfer case slip joint elim. kit [willybump] by erickpl
Dec 15, 2008 (5:39 am)
Reply

Replying to: willybump (Dec 12, 2008 10:54 am)

Lots of choices:
 
www.4x4groupbuy.com
www.4x4rockshop.com
www.northridge4x4.com
www.redrock4x4.com
 
Pretty much any reputable online 4x4 shop will have em. Go with a decent maker like Advanced Adapters.
 
You will likely also need to get at LEAST adjustable rear upper control arms to rotate the rear pinion up a bit bit to more appropriately line up the angle with the driveshaft. There are lots of writeups online about SYE (slip yoke eliminator) setups.
 
-Paul
#151 of 193
tires and wheels by bambam10
Jan 10, 2009 (7:27 pm)
Reply
I have a 2008 jeep wrangler x I have not done anything to it. I was wondering what size tires and wheels I can put on it with out haveing to lift it?
#152 of 193
Have I measured right? by mgarvie
Feb 04, 2009 (4:28 am)
Reply
I have an 06 Sport with, yuck, hubcaps! I wanted to get new rims and tires and wanted a second opinion if they will really fit. I don't go off road but do a lot of highway driving so I'm not going taller.
 
wheels 15x8 with 3.68 backspacing
 
tires 265/75R15
 
Am I OK here?
#153 of 193
Re: Have I measured right? [mgarvie] by erickpl
Feb 04, 2009 (5:14 am)
Reply

Replying to: mgarvie (Feb 04, 2009 4:28 am)

3.68" BS seems kinda high for a tire of that dimension if I'm reading it right. I have 33x12.5" and have 4.25" and would prefer to be at 4". In case you didn't know, the higher the BS number, the more 'tucked in' a wheel will be. So a 5.5" BS wheel will be tucked nicely (stock wheel) whereas a 3.75" BS wheel will stick out a bit more.
 
They should fit just fine, but may stick out a bit more than you want them to. It will be noisier as less tire will be muffled by the fender, and I guarantee you will be kicking up more water/dirt/grime on the highway...
 
Not advising against it, just advising on what you can possibly expect.
 
-Paul
#154 of 193
Re: Have I measured right? [erickpl] by mgarvie
Feb 04, 2009 (12:05 pm)
Reply

Replying to: erickpl (Feb 04, 2009 5:14 am)

I've been so concerned about the tires rubbing I didn't think about how far they would stick out. Guess I'll look around for something with a little more backspacing.
#155 of 193
Re: Have I measured right? [mgarvie] by erickpl
Feb 05, 2009 (6:07 am)
Reply

Replying to: mgarvie (Feb 04, 2009 12:05 pm)

More backspacing = lower number.
 
Less backspacing = higher number.
 
If you go with something about 3.75-4" you should be good, even if you go up in tire size a bit. 3.68 just seems a bit odd to me.
 
Here's 4.25" of backspacing with 33x12.5" tires.
 

 
3.68 would stick out about a half inch more, but keep in mind my tires are 12.5" wide (wheels are only 8" wide).
 
-Paul
#156 of 193
Re: Have I measured right? [erickpl] by mgarvie
Feb 05, 2009 (12:22 pm)
Reply

Replying to: erickpl (Feb 05, 2009 6:07 am)

Seems like everywhere I look the backspacing is somewhere between 3.25 and 3.75. I guess I'll just suffer through wet elbows when ever I run through a puddle with my arm out the window. Even though I think I've seen them all, can you recommend a web site for rims? I've been trying to get a 15x7 or 15x8 in a black gloss finish.
 
Thanks for the help!
#157 of 193
Re: Have I measured right? [mgarvie] by erickpl
Feb 06, 2009 (6:02 am)
Reply

Replying to: mgarvie (Feb 05, 2009 12:22 pm)

WAY too many to specifically mention any in particular. You looking for alloy or steel?
 
-Paul
#158 of 193
Re: Have I measured right? [erickpl] by mgarvie
Feb 07, 2009 (4:13 am)
Reply

Replying to: erickpl (Feb 06, 2009 6:02 am)

I've narrowed my choice of rims down to a couple. They're gonna have to stick out a bit but I can always get bigger fender flares if it's a problem. Now I have a bit of confusion on tires. As I understand it, 31's will fit without a lift or modifying the fenders, but it sure seems close to the top of the current plastic fender flare. Will I have any problems with them rubbing going over bumps? Also, with either 30 or 31 inch tires, what issues will I have with the spare? Am I looking at buying 5 tires either way I go?
#159 of 193
Re: Have I measured right? [mgarvie] by erickpl
Feb 09, 2009 (6:02 am)
Reply

Replying to: mgarvie (Feb 07, 2009 4:13 am)

30 or 31's won't be a problem with stock suspension/height. If 31's look closed, you may have older springs and they are sagging a bit.
 
30/31's will fit the stock tire carrier w/o issue. 32's and 33's may be a problem width/height wise if you are on stock wheels. An aftermarket tire carrier would likely be your safest bet in protecting your tailgate.
 
-Paul

Messages Page 16 of 20
1
...
13
14
15
16
17
18
19
20
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

You are here: [F] Forums / SUVs / Jeep Wrangler / Jeep Wrangler Tires and Wheels

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Learn More

2010 Jeep Wrangler

2010 Jeep Wrangler Rubicon SUV Shown

More Pictures

DoMore

Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics
Advertisement