Sign In Join 



Dodge Dakota Engine and Underhood Questions

378 messages,  Last post on Nov 25, 2009 at 9:20 PM

You are in the Dodge Dakota Forum. Your Host is kcram

What is this discussion about? Dodge Dakota, Engine, Truck


Messages Page 26 of 38
1
...
23
24
25
26
27
28
29
...
38
Prev
Next
Last
Go To Msg #
Search This Discussion

#248 of 378
i'm stumped...please help by mailee75
Feb 19, 2008 (9:37 pm)
Reply
Hi all, i'm having troubles with my dakota...it's a 94 sport, 3.9 automatic 2 wheel drive.
 
so, when i start the truck, it shimmies n shakes, if you give it gas while still in park, it has a high pitched whine that accelerates and goes down with the engine....can't figure it out....when you drive, it seems to be sluggish, like somethings holding it back, tranny seems to shift when it suppose to but hits hard and winds out a little when goin into 3rd....tranny fluide is full and doesn't look or smell burnt. we recently put on new brakes, rotors (on front), and rims with wider tires off a durango...but do not have a lift on it yet, so the tires rub a little, but they don't seem to be the problem as this is going on when the truck is in park and you give it gas.....
 
also, it's not throwing any codes....
 
 
 
any suggestions on what to try or what it could be? thanks in advance
#249 of 378
I hate mustangs! by unclemike007
Mar 01, 2008 (5:04 pm)
Reply
I've recently become a Mopar enthusist since my Procharged 383 S-10 was spanked by a 95' dakota with a procharged 360. With the S-10 days left behind I purchased a 94' dakota SLT, and with all the mustangs running around un-cheked I'm ready for a possible swap from a 318 to a 360 (bad valve knock!) But everyone warns me and no-one will help! Will some one help Me put these mustangs to rest! I just need the recipe, I'll cook it.
#250 of 378
Re: I hate mustangs! [unclemike007] by bpeebles
Mar 01, 2008 (9:02 pm)
Reply

Replying to: unclemike007 (Mar 01, 2008 5:04 pm)

How about this K-car? I was present to watch this happen. The crowd was laughing until the lights turned green.
 
Keep in mind that car in the other lane is a REAR DRIVE Toyota Supra with a turbocharged, twin-rotor Mazda engine.
 
That K-car is 4-cylinder FWD WITHOUT nitrous and it can blow away hondas, mustangs and most any other car. It is inexpensive to make those K-cars go fast. (just add turbocharger)
#251 of 378
Re: I hate mustangs! [unclemike007] by sjeffers
Mar 05, 2008 (6:43 am)
Reply

Replying to: unclemike007 (Mar 01, 2008 5:04 pm)

first you need a block reconditioned 0.020 over 360 LA type ,cast-iron stock stroke [3.58] crank , KBsilv-0-lite hypereutectic flat top 1.58-inch [pn 4876907 or 1.63-inch pn4876908 compression height , reconditioned forged steel,stock-length 6.123 inches the cam is up to you depen on how you want /where the power will work for you crane cam rocker arms shaft-mount 1.5:1 adjustable , double roller timing set , the heads aerohead chrysler 340/360 [915or587castings] reconditioned [stock iron castings with 2.02/1.60-inch valves,0.509-inch-lift springs,bronze guides,chrome-moly retainers,7-degree iocks,performer RPM intake and 750 cfm or holly injection should make 375hp-400/410lb-ft torque it all depends an cam shaft ,aluminum heads are good to ,good luk
#252 of 378
Re: I hate mustangs! [sjeffers] by unclemike007
Mar 06, 2008 (2:55 pm)
Reply

Replying to: sjeffers (Mar 05, 2008 6:43 am)

Thanks much! Sounds like I'll be setting up an acount with PAW and Jegs! I'll post pics and vid when I'm done. Angain thank You!!!
#253 of 378
Re: I hate mustangs! [sjeffers] by sjeffers
Mar 07, 2008 (11:55 am)
Reply

Replying to: sjeffers (Mar 05, 2008 6:43 am)

i forgot you will also need a harmonic ballecer the 360 is externaly balleced allso the flex plate if you use the one off your 318 you need a wait on the coverter .I just built a 93 360 but i used the stock intake do to funds .had to port the intake to match the 360 head ports .that is starving the pore girl but still runs good put stuby headers on and had custume exaust duels with hi flow converters and aero turbine mufflers igot a picture of the truck in carspace. hope to see what yougot see ya
#254 of 378
Re: I hate mustangs! [sjeffers] by unclemike007
Mar 08, 2008 (10:11 am)
Reply

Replying to: sjeffers (Mar 07, 2008 11:55 am)

I almost forgot! What about the motor mounts? Do I have to mess with relocating them or do I just get 360 mounts and button it up?
#255 of 378
Re: I hate mustangs! [unclemike007] by sjeffers
Mar 08, 2008 (7:40 pm)
Reply

Replying to: unclemike007 (Mar 01, 2008 5:04 pm)

just make sure that the block has the exstra mount holes ,look were your engine mounts are on you 318 thay bolt on like a chevy 3 bolts .got a engine built by S&S engine remanufacturing found it on GOOGLE it is a good start price is wright just ask for a short block then build it from there pull the 318 out and put the 360 in just remember the ballacer the torqconverter and the oil pan for 360 truck you got it made.
#256 of 378
Re: I hate mustangs! [unclemike007] by sjeffers
Mar 08, 2008 (9:42 pm)
Reply

Replying to: unclemike007 (Mar 08, 2008 10:11 am)

check this out buy hot rod April 08 theres a 360 buildup youl like that
#257 of 378
1997 dodge dakota 3.9 v6 2x4 by steve174
Mar 25, 2008 (2:50 pm)
Reply
hi i been having a problem with my truck the gages are not working and its not getting any spark. the problem started a few weeks ago it wouldn't start then a few day later it started. then it would just suddenly die. then would not start again then it started a few days later i drove it for about 15 mins around the block and parked it and it hasent started since.
 
thanks

Messages Page 26 of 38
1
...
23
24
25
26
27
28
29
...
38
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics

Today's Chats

Advertisement