Last post on Nov 11, 2013 at 5:16 AM
You are in the Pontiac Bonneville
What is this discussion about?
Pontiac Bonneville, Auto Repair, Sedan
#227 of 236 Re: 1995 pontiac bonneville se [casoriagag]
Sep 10, 2012 (5:59 am)
>--car shuts off even on the highway at 60 mph. Gives me these security lights and then drops the gas light as if I have no gas, shows it to empty and then the call stalls,
I would check the ignition switch carefully. I do not know anything about the physical arrangement of the parts on your car, but that ignition switch can have different contacts for different services. As it heats while the car's running, individual contacts can lose connection while others stay in contact. Heat, vibration, burning, can lead to the bad contact while running.
#228 of 236 2000 pontiac bonneville fuel pressure
Dec 28, 2012 (4:10 pm)
00 bonneville that will start and run but hit throttle and dies. Have replaced fuel filter, fuel pressure regulator, thought maybe cat was plugged but eliminated that and still runs like crap. Once it warms up, it will just start up and shut off. Will not hold fuel pressure with key on not running, once running has pressure, not sure how much dont have guage. Have checked all vacuum lines and cannot find any leaks. When I first start it up I can drive it down road and seems to go ok but if you kick it down seems to not have a lot of power or cuts out funny. Have been digging around a bunch and am stumpped. Any help or ideas would be appreciated. thanks
#229 of 236 Re: Car died [tamwa]
Jan 08, 2013 (12:42 pm)
hello tamwa, did you get your problem resolved? If you did could you post on here what you did to get it going again.
I am having the same kind of problems with my '96 bonneville ssei supercharger.
#230 of 236 Re: 2000 pontiac bonneville fuel pressure [yamiracer]
Jan 08, 2013 (2:58 pm)
You need to verify your fuel pressure. You can get loaner pressure gauges at certain auto parts stores in this state of Ohio. Don't know where you live.
The pressure should be tested with the engine off and the key on. The pump will run a couple seconds and then shut off. The pressure should hold unless there's a bleed down from a leak or the fuel pump. Then the pressure should be checked with the engine running at idle, and then the pressure noted when the engine is accelerated causing the vacuum to reduce which lets the fuel pressure regulator up the pressure.
Second choice would be the MAF sensor may need cleaning.
#231 of 236 Re: 1994 bonneville shuts down [denny115]
Mar 07, 2013 (9:24 am)
ive heard a lot of horror stories about it being a feul pressure regulator and if not fixed can be very bad for both the car and you .it can pool gas in the intake and explode the intake off.there about 60 bucks
Mar 07, 2013 (9:25 am)
also there is a ground under the kick plate on the driver side that gets corroded and can cause all kinds of fits
#233 of 236 Re: 2000 pontiac bonneville fuel pressure [yamiracer]
Mar 10, 2013 (4:56 pm)
I had this problem late last year. It is related to the MAF sensor. Worn motormounts created stresses that "tugged" on the MAF sensor and caused it to malfunction. Replacement of one of the motormounts helped, along with a MAF sensor cleaning. I still need to replace the second motormount and probably should replace the MAF sensor as well, even though it is only about three years old. So far, I've spent about $350 on this problem. I have a 2002 Bonneville with a non-supercharged 3.8 Liter V6. Hope this helps.
#234 of 236 intermittent rough idling
Oct 26, 2013 (10:34 am)
95 bonneville ssei, 90,000 miles. I am having a variation in my idle. It at times is smooth, slightly rough, very rough, and choppy. This can all take place within a 10 minute period. Any thoughts on what it can be? We've tried 2 computer replacements, 02 sensor. Please help?
#235 of 236 Re: Wont start, only clicks. [92bonny]
Nov 10, 2013 (6:23 pm)
Yes. I had a similar issue 7-8 years ago. Your have a Pass-Key theft deterant system. Your key has a tiny chip in the shaft of the key that is picked up by a couple of clips inside your ignition lock cylinder. Over time, especially with keys that are attached to large/heavy key chains, the chip wears down, or damages the clips in the ignition lock cylinder. I had both probems present. I needed a new ignition lock cylinder and a new set of ignition keys. Once that was done, problem never surfaced again. Your owners manual will tell you what your car normally does relative to the theft determant system, and what happens when a non-conforming key is used. I'll bet if you read that, your system is telling you that you are using a non-conforming key (subtle method with a blinking light). If that is your case, you know you need either new ignition keys or a new ignition lock cylinder, or both.
#236 of 236 Re: Wont start, only clicks. [93celicaconv]
Nov 11, 2013 (5:16 am)
92bonny's post is from 2010. He hasn't logged in on Edmunds since March 20, 2010.
But for others reading this, I'd like to offer a cheaper way to handle VATS problems where the security light blinks for 3 minutes AFTER the key is turned indicating it's getting a wrong reading on the resistance through the key.
The owner can identify the usually orange tube that has two fine white wires in it that comes from the ignition switch (not the lock) and goes to the connector on the firewall above the parking brake. Cut those nearer the steering column to leave some slack. Put in soldered resistors in series that add up to the resistance on the key chip, within 5% or so. Usually that will fool the TDM (theft deterrent module) into thinking the same key resistance is presence. This will cost a dollar or two for resistors from Radio Shack if you are able to do the soldering and locating work yourself.
The usual break point for the two fine wires is where the tilt column is flexed every time it's moved. The contacts in the lock also do wear and cause trouble along with a dirty key contact. So bypassing the whole mess eliminates the antitheft protections, but saves a whole lot of money.
Locating the orange tube with white wires inside that looks like a solid orange power wire is the hardest part. There are youtube videos that show some of this.