You are here: Forums SUVs Chevrolet Blazer 98 Blazer Door Panels

98 Blazer Door Panels

7 messages,  Last post on Nov 03, 2008 at 4:15 PM

You are in the Chevrolet Blazer Forum. Your Hosts are steve_ & tidester

What is this discussion about? Chevrolet Blazer, GMC Jimmy, SUV

Messages Page 1 of 1 All Messages Displayed

Go To Msg # Search This Discussion

#1 of 7 98 Blazer Door Panels by brgray Oct 09, 2006 (8:05 am)
I'm trying to replace the mirror on the passanger side and am having a difficult time removing the door panel. I've removed the screw behind the door handle, as well as the two nuts in the arm rest. I must be missing something else because it sure doesn't seem to want to come off. If anyone has any info. I'd appreciate it. Thanks. Replies to this message: repairdog (Oct 09, 2006 8:20 am) brgray (Oct 09, 2006 11:16 am)
#2 of 7 Re: 98 Blazer Door Panels [brgray] by repairdog Oct 09, 2006 (8:20 am)
Replying to: brgray (Oct 09, 2006 8:05 am) Thats it - you did mean the 2 small bolts under the arm rest so then start at the bottom and pry the panel up and then pull out - lots of plastic push connectors and then the top has a lip over and into the door window frame so lift up and off. The power controls lift/snap off and simply drop it thru the panel. Then you can get to the 3 mirror nuts after popping teh rubber plugs out. Replies to this message: brgray (Oct 09, 2006 11:16 am)
#3 of 7 Re: 98 Blazer Door Panels [repairdog] by brgray Oct 09, 2006 (11:16 am)
Replying to: repairdog (Oct 09, 2006 8:20 am) Thanks for the help, man. Got it working all better now.
#4 of 7 98 Jimmy window by rocky33 Mar 17, 2007 (6:32 pm)
I replaced the window regulator and now the window does not track correctly. It goes sideways. Any help would be apreciated. I can not find a picture of the door interior to see if there is something missing. Replies to this message: repairdog (Mar 20, 2007 12:44 pm)
#5 of 7 Re: 98 Jimmy window [rocky33] by repairdog Mar 20, 2007 (12:44 pm)
Replying to: rocky33 (Mar 17, 2007 6:32 pm) Sounds like you didn't get one of the scissors roller ends in the channel - look again - believ 4 of them and a pain to get them all in.
#6 of 7 '84 Blazer S10 by mgeweke Oct 03, 2007 (7:05 am)
I removed all the screws from the drivers door, popped the plastic body panel loose but cannot get the window handle off and therefore cannot completey remove door panel to reset window in track.   how to remove the window crank please? Replies to this message: blzr9991 (Nov 03, 2008 4:15 pm)
#7 of 7 Re: '84 Blazer S10 [mgeweke] by blzr9991 Nov 03, 2008 (4:15 pm)
Replying to: mgeweke (Oct 03, 2007 7:05 am) theres a screw in the center of the crank handle. once its removed, the handle should just pull out.   hope it helps

Messages Page 1 of 1 All Messages Displayed

Go To Msg # Search This Discussion

You are here: Forums SUVs Chevrolet Blazer 98 Blazer Door Panels