Ask the Car People.SM


Need some mechanical help in SF Bay Area

15 messages,  Last post on Mar 29, 2008 at 6:34 PM

You are in the Classic Cars Forum.

What is this discussion about? Chevrolet Camaro, Engine, Coupe

Messages Page 2 of 2

#7 of 15 Re: camaro just cranks over. [traviscoleman1] by oilman1

Nov 13, 2006 (10:00 pm)

Replying to: traviscoleman1 (Nov 12, 2006 6:19 pm)
Did you have the PCM scanned yet?I think you should get this car scanned before you throw any more parts at it.I still think its the coil,its a cheap part as well.Iam curious as the what the pressure difference is from the old pump to the new one,purhaps the pump was fine.I wouldnt use ether on my engine,Ive beaded heavy truck tires with that stuff,Id bet if you had spark and it caught you would know.

#8 of 15 Re: reply about camaro cranking over by traviscoleman1

Nov 14, 2006 (6:52 pm)

Replying to: oilman1 (Nov 13, 2006 10:00 pm)
I finally gave in and i had the car plugged into a computer. The old fuel pump was bad because it wasn't holding it's pressure it went to 41 then droped down, the new one starts at 47 and stays there it don't drop. But the computer said that one of my control moduels on my distributor was bad. So i am goin to replace that tommorw night and i will let you know if that fixes it or not.

#9 of 15 Need Help by curlysgirl

Dec 02, 2006 (12:33 am)

i have a "82 camaro and I am trying to rebuild the engine.... I am almost done!!!! But i need to torque down my heads.... i need to find out the torque specs on a 305 chevy.... can anyone help??

#10 of 15 Need Help by curlysgirl

Dec 02, 2006 (12:36 am)

i have "82 camaro with a 305 small block. I am trying to rebuild my engine. I am almost done!!! Alli need now is to torque down my heads.... does anyone know the specs for them??

#11 of 15 Need some restoration work in San Jose area by gatorj19

Apr 04, 2007 (5:16 pm)

I have a 1973 Pontiac Trans Am and am looking for a reputable and responsible shop to complete unfinished restoration. I have all of the parts needed-just need a good shop to finnish what was started. Engine and tranny already done and in car and is mostly cosmetic- interior and paint. Anyone out there with suggestions? Please help!
              
                Thank You,
                          Joanna

#12 of 15 Re: Need some restoration work in San Jose area [gatorj19] by isellhondas

Apr 17, 2007 (4:39 pm)

Replying to: gatorj19 (Apr 04, 2007 5:16 pm)
No good answer here.
 
Few shops are willing to take on a "basket case" where someone has started a restoration.
 
The places that will work on this car are going to charge probably 100.00 dollars per hour. A 1973 Trans Am won't be worth much when it's done so you might want to re-think this.
 
You might ask around to see if someone takes on side projects but be careful who you hire!

#13 of 15 Re: Need some restoration work in San Jose area [isellhondas] by texases

Apr 17, 2007 (5:58 pm)

Replying to: isellhondas (Apr 17, 2007 4:39 pm)
Tough situation. Maybe you'll have to break it down into, say, 3 steps (body, interior, mechanical) and get it towed from shop to shop. Probably not one single shop could do it for reasonable $$. You don't want a 'restoration' shop, just a reasonable body shop, interior shop, and a mechanic.

#15 of 15 Re: 84 camaro just dies while driving, no idea why? [510razd] by MrShift@Edmunds HOST

Mar 29, 2008 (6:34 pm)

I'm going to move this over to Technical Questions. See you there:
 
Technical Questions

Messages Page 2 of 2

To POST a message, please Sign In.

Advertisement

Browse by Category

Browse by Vehicle
   View All Vehicles

Browse by Board
Browse by Topic
View All Topics

Edmunds Community

Advertisement