Chrysler 300M Starting/Stalling problems

71 messages, Last post on Nov 30, 2009 at 3:16 PM

You are in the Chrysler 300M Forum. Your Hosts are pat & karens

What is this discussion about? Chrysler 300M, Sedan

This topic covers any issues related to hard starting, no starts, stalling and erratic idling problems.

Outline

Messages Page 8 of 8: 1; 2; 3; 4; 5; 6; 7; 8; Prev; Next; Last

#63 of 71 random stalling by rugga56 Jul 21, 2009 (7:35 am)
My 300M keeps on stalling. I have replaced my cam and crank sensors,ignition coils, spark plugs, timing belt, and fuel pump. Every time I easy in on the gas going between 10-60mph I just might stall. Does anyone have a solution that will fix this problem? Replies to this message: danfishinman (Aug 01, 2009 6:35 am)
#64 of 71 How I solved my stalling problem - EGR valve by danfishinman Jul 23, 2009 (1:02 pm)
I have a 2000 300M with 102K miles and it just recently started to stall on deceleration (off ramps and stop lights) but only after it had warmed up. It would re start ... but run rough and then stall again. Check engine light Never came on and no codes were stored BUT when i left my OBD scanner plugged in while driving I noticed a PENDING P0404 code...meaning that it was intermittent. P0404 is an EGR valve problem. I found one of the last EGR valves in the northeast last saturday ($180) and had my mechanic put it in (not an easy job) it took him 4 hours ($320) (had to deal with lots of old bolts) but it worked!!!! My car is now safe and fun to drive again.
#65 of 71 Re: random stalling [rugga56] by danfishinman Aug 01, 2009 (6:35 am)
Replying to: rugga56 (Jul 21, 2009 7:35 am) See my post on this page.. I bet its your EGR valve failing good luck
#66 of 71 Re: 99 wont start when hot [dsisco] by steveaaaaa Aug 13, 2009 (4:38 pm)
Replying to: dsisco (Aug 10, 2008 11:01 am) I too am having the same problem. A 1999 300m that is hard to start when its hot,after a long haul.If it was a carburated vihical I would assume it was a choke problem by the way its acting.In order to start I must do some serious fethering of the gas,but once its started it runs great.It only does it on a long haul shut off then restart.If I wait a halh hour it starts with no problem. Anyone ever figure it out?
#67 of 71 Re: Help get my 300c Started [rnaples] by william44 Aug 25, 2009 (10:50 am)
Replying to: rnaples (Nov 16, 2008 5:07 am) my 300m starts turn it off it will not start take wire off battery post for 10 min. it will start.
#68 of 71 300m stalls after warmup by roshea Sep 04, 2009 (9:42 am)
My car warms up and stall and will not restart till engine is cool. Code say manifold tuning valve. rplaced mtv and also the thing next to it that works off vacuum. I have also had a part changed in the transmissin because it was stuck in gear. the junck yard part are 10 a piece. What part next can you help Rich
#69 of 71 2002 300M won't start by dellagx Sep 28, 2009 (6:03 pm)
car was running fine all day, I came out the store after about 10 minutes and started it, it turned off immediately, no choking before doing so. It did this 3 times before it finally would not crank at all. The neutral switch and steering column have been replaced, battery has been checked, and I don't know what else to do. If the cam sensor is bad, would it be causing this? That is where I'm leaning right now, i will have to take it to a dealership soon if i can't figure it out.
#70 of 71 Re: 1999 chrysler 300m not starting [maizenblue989] by ad_marley Nov 19, 2009 (8:16 pm)
Replying to: maizenblue989 (Jun 30, 2009 5:25 pm) had a similar problem ( flashing lights while driving, off engine while driving, won't start couple times ) turn out to be a battery, I couldn't believe .
#71 of 71 not starting by 808josh Nov 30, 2009 (3:16 pm)
went camping not to long ago and my 99 300m was great, parked it, when we decided its time to go, it didnt want to start, it kicks over like it wants to start, but nothing, got it home and checked the code and it seemed to be the cam and crank sensor so we changed those YAY! still doing the same problem and still giving us the same code. any ideas on what it could be now? maybe have to reset the computer? HELP!!