You are here: Forums SUVs GMC Jimmy GMC Jimmy ABS Sensor

GMC Jimmy ABS Sensor

39 messages,  Last post on Nov 16, 2009 at 3:44 PM

You are in the GMC Jimmy Forum. Your Hosts are steve_ & tidester

What is this discussion about? GMC Jimmy, Brakes, SUV

Messages Page 2 of 5 1 2 3 4 5 Prev Next Last

Go To Msg # Search This Discussion

#8 of 39 Re: heater will not heat [jmeade] by repairdog Dec 06, 2006 (3:14 pm)
Replying to: jmeade (Dec 06, 2006 1:56 pm) Probably a clogged heater core so do as in post 6 above.
#9 of 39 Re: GMC Jimmy 2001 ABS Sensor [repairdog] by mswillia1 Dec 17, 2006 (3:01 pm)
Replying to: repairdog (Sep 07, 2006 1:57 pm) It looks replaceable, but where Can I buy one. I think I pulled wire too hard while doing some axle work. Replies to this message: repairdog (Dec 19, 2006 3:23 am)
#10 of 39 Re: GMC Jimmy 2001 ABS Sensor [mswillia1] by repairdog Dec 19, 2006 (3:23 am)
Replying to: mswillia1 (Dec 17, 2006 3:01 pm) At the dealer. Held in by 2 torx bolts and about 2 feet up theres a connector on the frame that unclips but has a plastic pin holding it to the frame so pop it out. Comes with the new hub also if thats needed.
#11 of 39 2001 BLAZER ABS by diablo3 Jan 08, 2007 (3:15 am)
THE BRAKE PEDAL ON MY BLAZER PUSHES BACK TO ME WHEN I APLPY PRESSURE AT 10 MPH OR LOWER AND MAKES SORT OF A GROANING NOISE. NO PROBLEM AT HIGHER SPEEDS I CALLED GM AND THEY TOLD ME IT'S PROBALLY A WHEEL SPEED SENSOR TO HAVE THEM CHECKED AND CLEANED OFF AND THAT WILL SOLVE THE PROBLEM. I WENT TO A DEALERSHIP AND THEY TELL ME IT'S THE ABS AND THEY WILL HAVE TO REPLACE IT. I HAVE AN APPOINTMENT FRIDAY TO HAVE THEM CHECK IT. IS THE DEALER TRYING TO RIP ME OFF ASSUMING THAT IT'S THE ABS WITHOUT CHECKING IT YET. I'M SURE A WHELL SPEED SENSOR CLEANING OR REPLACEMENT IS A LOT CHEAPER THAN REPLACING THE ABS SYSTEM. THANKS Replies to this message: repairdog (Jan 08, 2007 2:21 pm) gdell (Nov 20, 2007 6:00 am)
#12 of 39 Re: 2001 BLAZER ABS [diablo3] by repairdog Jan 08, 2007 (2:21 pm)
Replying to: diablo3 (Jan 08, 2007 3:15 am) Have to read the codes out with a tech 2 scanner first to confirm. If in salt use areas the rust builds up and raises the sensor out of spec so have to unbolt the sensor and carefully sand the mating surface and not get any crap in the hole and in the hub, if thats the problem. Check the wires from the sensors up to the connector on the frame for cuts first on the fronts. Rear sensor is on the trans 2wd and transfer 4wd. Hub bearings (one piece asembly)going may also cause this but you would hear it also normally.
#13 of 39 2000 jimmy evap sys by painhead Jan 24, 2007 (5:05 pm)
took my jimmy to auto zone had it put on code tester came up with po452 code pressure low then another code po453 pressure high... any idea's? Replies to this message: repairdog (Jan 25, 2007 2:23 am) painhead (Jan 26, 2007 9:10 am)
#14 of 39 Re: 2000 jimmy evap sys [painhead] by repairdog Jan 25, 2007 (2:23 am)
Replying to: painhead (Jan 24, 2007 5:05 pm) Specifically for those 2 codes no but heres the circuit descrition form the odb-codes site:   This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine. Symptoms: You likely won't notice any drivability problems. Causes: A code P0440 could mean one or more of the following has happened: The gas cap is not installed or working properly The purge solenoid has failed The canister is plugged and not working properly Replies to this message: painhead (Jan 26, 2007 9:10 am)
#15 of 39 2001 CHEVY BLAZER ABS by diablo3 Jan 25, 2007 (2:43 am)
ONCE I TOLD THE DEALER THAT IT WAS SPEED SENSOR AND NOT THE ENTIRE ABS SYSTEM, HE THOUGHT I KNEW ABOUT SUV'S AND REPLACED MY LEFT FRONT SPEED SENSOR. EVERYTHING IS FINE NOW THANKS TO YOU GUYS. HE DIDN'T TRY A SECOND TIME TO TELL ME IT WAS MY WHOLE ABS SYSTEM. THANKS GUYS !!!!! Replies to this message: rkoppen (May 24, 2007 3:57 pm) rybeck3 (Jul 04, 2009 1:02 pm)
#16 of 39 Re: 2000 jimmy evap sys [repairdog] by painhead Jan 26, 2007 (9:10 am)
Replying to: repairdog (Jan 25, 2007 2:23 am) it was the canister it was pluged big time so i put a new one on it and now no problems at all....thanks a million
#17 of 39 Re: 2001 CHEVY BLAZER ABS [diablo3] by rkoppen May 24, 2007 (3:57 pm)
Replying to: diablo3 (Jan 25, 2007 2:43 am) I am curious, do you know how the shop figured which sensor did did nor work?   Have the same problem with my 99 yukon,   Looking forward to your response   Reinhard

Messages Page 2 of 5 1 2 3 4 5 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums SUVs GMC Jimmy GMC Jimmy ABS Sensor