- #1260 of 1282
-
Re: Minor Tranny Problems [bobwinner]
by behawke
-
Nov 11, 2009 (2:29 pm)
-
|
|
Replying to: bobwinner (Nov 11, 2009 8:32 am)
it circulates when u give some throttle but will not circulate  idle. where would the the check ball be located. I know theres 1 in the tranny line already toke it out is that the only 1 or is there more??
|
- #1261 of 1282
-
Re: ram 1500 transmission line pressure [dustyk]
by 87camaroguy
-
Nov 11, 2009 (8:26 pm)
-
|
|
Replying to: dustyk (Oct 09, 2006 4:32 pm)
you guys do know there is a valve not sure of the name of it but on my 96 ram its for vaccum and that piece rotted out and the truck was acting up shifting wise that turned out to fix the majority of the problems with that.
|
- #1262 of 1282
-
Re: 2006 Ram Quad Cab transmision sliping [sluggo333]
by 87camaroguy
-
Nov 11, 2009 (8:30 pm)
-
|
|
Replying to: sluggo333 (Nov 01, 2006 10:16 am)
Sluggo333 that is normal in all cars or trucks in the cold or cool temps reason being the fluid in the trans hasnt warmed up enough yet so it takes a minute to fully flow tray warming the truck up for about 5 to 10 minutes before you take off on a cold day.
|
- #1263 of 1282
-
2003 2500 45rfe trans error codes p0700,p0740
by ramtow1
-
Nov 12, 2009 (10:59 am)
-
|
|
has anyone hads these codes p0740 p0700 the trans shifts fine just making a electronice wine shuddererd once one code is a tcc eror torq converter the other is a low line pressure fault please any suggestions
|
- #1264 of 1282
-
Re: 2003 2500 45rfe trans error codes p0700,p0740 [ramtow1]
by bobwinner
-
Nov 12, 2009 (12:51 pm)
-
|
|
Replying to: ramtow1 (Nov 12, 2009 10:59 am)
With LOW LINE PRESSURE I automatically suspect a bad check valve. Feel of your tranny cooler. If it isn't hot, the problem is almost certainly a check ball.
|
- #1265 of 1282
-
1264 of 1264 Re: 2003 2500 45rfe trans error codes p0700,p0740 [ramtow1]
by ramtow1
-
Nov 12, 2009 (1:05 pm)
-
|
|
where is this check valve what about the wine almost tinny sound the tcc enable soleniod cercuit electrical
|
- #1266 of 1282
-
front seal leaking
by jclell21
-
Nov 15, 2009 (9:33 am)
-
|
|
the front trans seal was leaking and i replaced it. when the truck ran for awhile the knew seal did the same. anyone know what could cause that?
|
- #1267 of 1282
-
Re: front seal leaking [jclell21]
by 87camaroguy
-
Nov 15, 2009 (9:54 pm)
-
|
|
Replying to: jclell21 (Nov 15, 2009 9:33 am)
high pressure either there is too much fluid or that damn ball in the line is locked try changing the lines if the fluid is fine go to a place that sells transmission hose autozone sells it for like 2 bucks a foot and trust me i work for em the hose takes alot of abuse my dads ram is a great example.
|
- #1268 of 1282
-
Re: no movment while cold [artdallas]
by dfellows5
-
Nov 16, 2009 (6:51 am)
-
|
|
Replying to: artdallas (Sep 24, 2009 6:08 pm)
Did you figure out what the problem was?? I am having the same problem on my 2006.
|
- #1269 of 1282
-
Re: V8 5.9 RAM 94 4x4 engaging problems..Why does the truck jumps?? [ricardo_09]
by bobwinner
-
Nov 16, 2009 (7:16 am)
-
|
|
Replying to: ricardo_09 (Nov 09, 2009 9:45 pm)
When you use 4 wheel, all your tires try to turn at the same time and same speed. If the road is slippery (mud or snow) things seem smooth because slipping occurs with no problem. If the road is not slippery, you are actually forcing some tires to slip, which is why your jumping took place. This indicates your 4x4 is working. Then you may have shifted to 2 wheel, but you should have backed up a couple feet because your tranny actually stayed in 4 wheel until you heard that load noise. When putting into or out of 4x4, use reverse for a few feet. bobwinner
|
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
Pickups 
