You are here: Forums Pickups Dodge Ram Dodge Ram Transmission Problems

Dodge Ram Transmission Problems

1284 messages,  Last post on Dec 03, 2009 at 10:52 PM

You are in the Dodge Ram Forum. Your Host is kcram

What is this discussion about? Dodge Ram Pickup 1500, Dodge Ram Pickup 2500, Dodge Ram Pickup 3500, Transmission, Truck

Messages Page 115 of 129 1 ... 112 113 114 115 116 117 118 ... 129 Prev Next Last

Go To Msg # Search This Discussion

#1141 of 1284 96 dodge ram 1500 318 4x4 518 transmission by jarod82 Jul 29, 2009 (7:12 pm)
BEFORE : took off and shift to 2nd good and strong but when went into 3rd would raise rpm only 200 rpm before shift and shift to drive gear. KNOW: 1st hesitates and when it clunks then it will go. every so often on that. But when it goes its fine untill 3rd gear and i have to put it in neutral and back into drive with no reving it up and it shift fine into 3rd. and drive and overdrive is fine as well. push the overdrive button off and it shift out and back into OD. Just 3rd gear is the most problem.. I think its the OD Silinoid. or shift Silinoid. It doesnt slip at all. just shifting problem. SOME ONE PLEASE HELP. THANKS Replies to this message: reelgreaser (Aug 01, 2009 8:29 am)
#1142 of 1284 '99 Ram 1500 4x4 autotrans by reelgreaser Jul 31, 2009 (5:29 pm)
Truck ran fine this morning, went to leave work later that day and it felt like it was slipping a little bit when I first took off. Got on the on ramp and noticed it would not shift unless I let up on the gas a little, then I noticed the RPM's were running a little too high and realized my OD was not engaging, even when you push the OD button.Thought I smelled tranny fluid, so I pulled over checked fluid levels, they are fine. The check engine light came on, but no tranny lights are on. This truck is a '99 with 73,000 miles on it. Once you're moving it doesnt feel like it's slipping but it will not shift on it's own. It will manually shift fine. but no over drive at all! Replies to this message: reelgreaser (Jul 31, 2009 5:33 pm) reelgreaser (Jul 31, 2009 9:28 pm)
#1143 of 1284 Re: '99 Ram 1500 4x4 autotrans [reelgreaser] by reelgreaser Jul 31, 2009 (5:33 pm)
Replying to: reelgreaser (Jul 31, 2009 5:29 pm) I'm taking the truck in on Monday to have it looked at, when I (IF) get an answer from the mechanic I will post it. Hopefully I can help someone else out.   I have found alot of dodge tranny problems on the internet. I will be selling this one as soon as possible! This is a really nice truck to bad dodge won't help the mopar man!
#1144 of 1284 Re: '99 Ram 1500 4x4 autotrans [reelgreaser] by reelgreaser Jul 31, 2009 (9:28 pm)
Replying to: reelgreaser (Jul 31, 2009 5:29 pm) Just borrowed a code reader, came back with error code P0720 "Output speed sensor curcuit." located on the side of the tranny. $30.00 part. Hopefully it that's the only issue. let ya know..
#1145 of 1284 Re: 96 dodge ram 1500 318 4x4 518 transmission [jarod82] by reelgreaser Aug 01, 2009 (8:29 am)
Replying to: jarod82 (Jul 29, 2009 7:12 pm) I would try and replace the "output speed sensor", my problem sounded alot like yours does. I replaced the sensor ($20.00) this morning took ten minutes. Now the tranny is shifting and rumming smooth as new. remove the negative terminal from the battery for about tem minutes to reset the engine lights. the only tools you need are a 1" socket and a screw driver. Hope this helps. By the way the sensor is on the side of your tranny (Plastic)
#1146 of 1284 1998 1500 4x4 by jgwii Aug 01, 2009 (12:35 pm)
started having a gear grinding noise in transfer case seems to be getting worst can anyone help me with this?
#1147 of 1284 2001 dodge 2500 4x4 diesel by honeyman2 Aug 06, 2009 (5:00 am)
My trans keeps going in and out at 49 to 52 mph .and now its doing it at about 30mph .If I keep giving it fuel it shiftd like its suppose to .Could it be my TSP? Replies to this message: jay1164 (Aug 18, 2009 8:40 am) augiedoggy (Aug 19, 2009 2:05 pm) bulldog77 (Aug 19, 2009 4:14 pm) jay1164 (Aug 30, 2009 12:59 pm) bulldog77 (Aug 20, 2009 4:13 pm)
#1149 of 1284 how do I program my remote by bobwinner Aug 07, 2009 (6:39 am)
I lost my door remote (2003 Dakota), but have another remote now. Can I self program (and how, please) or must I go to the dealer to get it programmed?? bobwinner Replies to this message: kwitt (Aug 08, 2009 11:01 pm) bobwinner (Aug 09, 2009 6:22 am)
#1150 of 1284 Re: how do I program my remote [bobwinner] by kwitt Aug 08, 2009 (11:01 pm)
Replying to: bobwinner (Aug 07, 2009 6:39 am) I used to work at a dealership and you have to program the remote with the scanner. they also must be reprogramed at the same time. If you only program a new one you won't be able to use the old one that was working. The good news is it should only take 5 to 10 minutes to reprogram them. It usually took more time to find which module it was run through, it is different on some models, once you had the scanner hooked up. kwitt Replies to this message: bobwinner (Aug 09, 2009 6:22 am)

Messages Page 115 of 129 1 ... 112 113 114 115 116 117 118 ... 129 Prev Next Last

Go To Msg # Search This Discussion

You are here: Forums Pickups Dodge Ram Dodge Ram Transmission Problems