Sign In Join 

You are here: [F] Forums / Sedans / Toyota Camry / Toyota Camry Fuse and Electrical Questions



Toyota Camry Fuse and Electrical Questions

872 messages,  Last post on Dec 05, 2009 at 1:27 PM

You are in the Toyota Camry Forum. Your Hosts are pat & karens

What is this discussion about? Toyota Camry, Electrical, Sedan


Messages Page 57 of 88
1
...
54
55
56
57
58
59
60
...
88
Prev
Next
Last
Go To Msg #
Search This Discussion

#559 of 872
Re: No Windows Work 98 Camry [jamathi] by wwest
May 01, 2009 (5:52 pm)
Reply

Replying to: jamathi (May 01, 2009 3:45 pm)

Many newer systems have a temperature sensitive resistor in series with the window motor to protect it, the longer current flows to the motor the higher the resistance becomes.
 
Once the resistor "overheats" it will take awhile for it to cool down enough to have full power to the motor again. Try a silicon spray lub on the visible window guides/runners and if that doesn't help you may have to remove the door panel and lub the interior workings.
#560 of 872
Re: No Windows Work 98 Camry [wwest] by jamathi
May 02, 2009 (12:09 am)
Reply

Replying to: wwest (May 01, 2009 5:52 pm)

I've tried the silcone lubricant in the visible guides before and was surprised that it didn't make a difference. I'll open it up and lub the regulator, will with hi-temp grease work fine? If that does not work, should I look into replacing the regulator or something else?
 
Thanks for the advice.
#561 of 872
Re: No Windows Work 98 Camry [jamathi] by alphawolff
May 02, 2009 (9:26 am)
Reply

Replying to: jamathi (May 01, 2009 3:45 pm)

I had a similar problem on my wife's 98 Camry (this was a different problem than my most recent set of posts). I replaced the regulator assembly and still had the same problem. It turned out it was the switch itself. Carbon had developed on the switch contacts so the switch did not close completely. As this problem developed overtime it first manifested itself when the motor was under its heaviest load (when the window is going up). If you take apart the drivers side switch assembly there are four individual switches that plug int the PC board. I switched the drivers switch for one in the back. Now the driver can't roll down one of the rear windows but the driver s window works fine.
 
Hope this helps
#562 of 872
'89 CAMRY can't find the INTEGRATION RELAY! by capndavy
May 07, 2009 (3:08 pm)
Reply
My Maintenance manual has the relay mentioned on the BE-8 " Location of Switches and Relays" but there is no picture of the relay, only it's name, no arrow.
It is listed in the Fuse Block #1 group in parenthesis.
 
I have exposed the Fuse Block under the Driver's side kick panel but cannot identify the INTEGRATION RELAY. It is not labeled on BE-11 either ("Fuse and Relay Blocks").
 
I need to change this relay but can't find it and don't know what it looks like.
Can someone help please?
 
Thanks in advance-
-Dave
#563 of 872
Re: '89 CAMRY can't find the INTEGRATION RELAY! [capndavy] by kiawah
May 07, 2009 (4:44 pm)
Reply

Replying to: capndavy (May 07, 2009 3:08 pm)

It's on the 'backside' of that relay block, down on the bottom.
#564 of 872
Re: '89 CAMRY can't find the INTEGRATION RELAY! [kiawah] by capndavy
May 08, 2009 (4:38 am)
Reply

Replying to: kiawah (May 07, 2009 4:44 pm)

Thank you KIAWAH.
 
I noticed a largish screw or bolt head at the bottom of the fuse block. Is that the only fastener??
(I can't see the top edge of the fuse block)
 
Thanks again!
-Dave
#565 of 872
Re: '89 CAMRY can't find the INTEGRATION RELAY! [capndavy] by kiawah
May 08, 2009 (5:04 am)
Reply

Replying to: capndavy (May 08, 2009 4:38 am)

That's right.
 
The integration relay for that year is a big square like thing right above that bolt hole, on the backside.
 
By the way, what was the original problem/symptoms that you were having, and how did you conclude that the integration relay was bad and needs to be replaced?
#566 of 872
2001 camry blowing guage, window fuse by jillier
May 14, 2009 (12:25 pm)
Reply
Hi, I am having a problem with fuse 22 blowing that controls guages, power windows, charging system, etc. I replaced it yesterday, and drove 8-10 miles today, then it blew again. Any clue as to where I might look first? Also will the computer show any info? Thanks.
 
John
#567 of 872
Re: 2001 camry blowing guage, window fuse [jillier] by kiawah
May 14, 2009 (12:57 pm)
Reply

Replying to: jillier (May 14, 2009 12:25 pm)

I'll try to help you out here, but which fuse is it that is blowing. I don't know of a fuse called 'fuse 22'. What is the amperage of the fuse that is blowing, which fuse box is it located in, and what is the label next to the fuse (or alternatively, where is it located in the fuse box).
 
For instance, looking for something like:
- it is the 30Amp AM2 fuse that is blowing, or
- it is the 10Amp Gauge fuse that is blowing, or
- it has a marking of 30A, and it is in the engine compartment fuse box on the left fenderwall, and in the lower right corner of that fuse box next to another fuse marked 30A RDI
#568 of 872
Re: 2001 camry blowing guage, window fuse [kiawah] by jillier
May 15, 2009 (2:06 pm)
Reply

Replying to: kiawah (May 14, 2009 12:57 pm)

it is the 10a guage fuse that is blowing, it also covers power windows, charging system, back-up lights.
 
John

Messages Page 57 of 88
1
...
54
55
56
57
58
59
60
...
88
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

You are here: [F] Forums / Sedans / Toyota Camry / Toyota Camry Fuse and Electrical Questions

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Learn More

2010 Toyota Camry

2010 Toyota Camry LE Sedan Shown

More Pictures

DoMore

Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics

Today's Chats

Advertisement