Ask the Car People.SM


Toyota Camry Basic Maintenance Questions

678 messages,  Last post on Sep 02, 2012 at 6:55 AM

You are in the Toyota Camry Forum.

What is this discussion about? Toyota Camry, Toyota Camry Solara, Oil, Sedan

Messages Page 67 of 69

#657 of 678 Re: 2000 Toyota Camry V6 60K maintanance - How much will it cost [2000camryv6] by 210delray

Nov 02, 2010 (10:34 am)

Replying to: 2000camryv6 (Nov 01, 2010 8:23 pm)
There is no "normal" price. It depends on where you take the car (dealer vs. chain store vs. independent shop), and it varies depending on how each shop defines the "60K" maintenance. I'd look at the maintenance manual and see what Toyota recommends, then list each of these items and ask how much a given shop will charge for them. Items on the list will include replacing the oil and filter, coolant, air filter, spark plugs, rotating the tires, and checking the suspension, steering, and brakes. Maybe you (or they, if they're honest) can figure out what was already done before you bought the car. If the tires are evenly worn, you can skip rotation, although the tires/wheels have to come off anyway for the brakes to be checked.
 
The check engine light may not be related to any of the items listed in the 60K maintenance interval -- so without a diagnosis, it's not possible to estimate what the charge for a remedy might be. You can get an auto parts store like Auto Zone, Advance, or NAPA to read the code for the check engine light (for free), then look it up on the internet to see what the code might mean.

#658 of 678 2004 Camry Serpentain belt by jjoseph2

Nov 11, 2010 (3:45 pm)

Can any one tell me how to replace the serpentain belt on a 2004 Totota camry

#659 of 678 Re: 2004 Camry Serpentain belt [jjoseph2] by kiawah

Nov 11, 2010 (8:27 pm)

Replying to: jjoseph2 (Nov 11, 2010 3:45 pm)
Without looking it up in the manual, the typical setup is there is a spring loaded belt tensioner, In order to unload the tension on the tensioner, you put a tool into it. I've had vehicles that you use a large pry bar screwdriver, a 3/8" or 1/2" shank socket pry bar, and I've had vehicles with a socket head (like a 5/8 or 3/4".
 
You connect the applicable tool to the tensioner, and with the power leverage put pressure in the direction which will unload the tension. The belt will begin to get loose, and with your 2nd hand take the belt off one of the pulleys so when you gently let the tensioner back is moves back easily. Don't let it snap back.
 
Take the old belt off, pay attention as to the routing of the belt around the different pulleys. Typically there is a graphic under the hood on all vehicles, which shows you how the belt is supposed to route.
 
It can be tight working the belt into the correct position. Depending upon how the belt is routed on any vehicle, you may have to unbolt an engine support bar. Other vehicles you also take out an access panel behind the front right wheel.
 
Work the new belt into the proper position to all but one of the pulleys, put tension back on the tensioner so you can get the belt into final position, and ease up on the tool again so that the tensioner is riding on the belt correctly. You also want to make sure the belt sits on all of the pulleys correctly. You don't want it to be off a groove, or your belt won't last long.
 
Depending on the vehicle manufacturer, model, make, year, and engine.....this can be a 10 minute job, or more than an hour.
 
It can be common to have a bad tensioner, either the pulley on the tensioner is bad, or the spring is bad. If this is the case, then while you have the belt off, you unbolt the whole tensioner assembly off the side of the engine and replace it with a new one, then put a new belt on as described above.
 
Good luck.
 
Edit:
Just found a general ehow, watch this:
 
belt off
 
belt on
 
Actually, there are a whole series of these, dealing w/serpentine belt and pulleys.

#660 of 678 2007 Toyota Camry 4 Cyl, LE by masterpt1

Jan 29, 2011 (5:58 pm)

Ooopps! I just broke off the two inner hinges of my air filter housing due to the fact that I bought the wrong size (barely too large) filter. I put the old filter back in and secured the two bolts and ran the engine for a few minutes with some revving here and there and the engine sounded fine. Has anyone else broken the hinges and if so, have you had good luck with maintaining a consistent vacuum/seal just using the two bolts??

#661 of 678 fuel filter by choochooman

Feb 03, 2011 (8:51 am)

haven't seen anything on replacing fuel filter nor the pcv? have 05 v6 le 38k, and 04 highlander v6 48k has anyone had these done?

#662 of 678 Re: 2007 Toyota Camry 4 Cyl, LE [masterpt1] by 210delray

Feb 03, 2011 (7:36 pm)

Replying to: masterpt1 (Jan 29, 2011 5:58 pm)
I wouldn't chance it; I recommend buying a replacement upper housing (the part with the hinges).

#663 of 678 Re: fuel filter [choochooman] by 210delray

Feb 03, 2011 (7:37 pm)

Replying to: choochooman (Feb 03, 2011 8:51 am)
Neither require regular service. From what I understand, the fuel filter is inside the fuel tank.

#664 of 678 Service needed by dano51

Feb 13, 2011 (1:51 pm)

2006 Camry xle 6cyl what is service recomended at this point .I like to prevent serious things from happening.When should I consider changing timing belt. I am sorry I have 40,000 on it now have done nothing but oil and filter
Thanks Dano

#665 of 678 Dogbone upper motor mount by metalibrarian

Mar 13, 2011 (9:29 pm)

On my 2004 Camry 4-cyl LE there is a strut on the top passenger side that keeps the engine stable. It has many names including 'dogbone' (which it looks like) and 'torque motion control arm'. It has hard rubber bushings at each end, which get brittle over the years and disintegrate, as mine have done. Replacing this 90-buck part should task about ten minutes. Anybody have any difficulties with this operation? Like lining up the bolts once you've put the new dogbone in place? I hate to pay a mechanic for such a simple operation but will if any of you have run into trouble.

#666 of 678 Re: Dogbone upper motor mount [metalibrarian] by camryguy3

Mar 14, 2011 (1:13 am)

Replying to: metalibrarian (Mar 13, 2011 9:29 pm)
you didnt mention how many miles were on your car....I have a 2000 camry w/200k on it and never replaced the motor mounts...those are designed for the life of the car unless involved in an accident to which they break away from the motor to prevent occupant injury...if you have some sort of vibration...it may be a different issue. The part is inexpensive...but a pain if you don't have the equiptment to replace it

Messages Page 67 of 69

To POST a message, please Sign In.

Advertisement

Browse by Category

Browse by Vehicle
   View All Vehicles

Browse by Board
Browse by Topic
View All Topics

Edmunds Community

Advertisement