- #17 of 88
-
Exact same problem
by frozennugget
-
Feb 22, 2007 (7:00 pm)
-
|
|
Replying to: expo1 (Dec 03, 2006 7:56 pm)
Expo1, did you ever get this one solved? I have a similar problem. '98 Explorer with 101K miles. The 4WD High and Low indicator lights blink 5-6 times a minute.
|
- #18 of 88
-
Re: Exact same problem [frozennugget]
by expo1
-
Feb 25, 2007 (8:55 am)
-
|
|
Replying to: frozennugget (Feb 22, 2007 7:00 pm)
no, i found that this only happens when its cold outside around 45 and below. read that the code for lights flashing 6 times to check 1) clutch & front sensor connectors. 2) clutch coil. 3) internal circuitry sensor have discontinvity. hope this helps, let me know.
|
- #19 of 88
-
2002 4x4 EB Explorer
by rocky32
-
Feb 25, 2007 (10:14 am)
-
|
|
Replying to: steve_ (Apr 12, 2007 2:07 pm)
My 4x4 switch will not light up or engage to 4x4. Does anyone know what the problem is...Thank you
|
- #20 of 88
-
4x4 problem
by news1
-
Feb 27, 2007 (9:18 pm)
-
|
|
Replying to: steve_ (Apr 12, 2007 2:07 pm)
Hello, I have a 2002 ford explorer and i had problem with my battery that went dead few months ago.After changing the battery, my 4x4 light never comes on again; I checked my fuses,everything is allright; Can I get any help for this situation if someone can.
Thank you.
|
- #21 of 88
-
4x4 flashing lights
by newdavidq
-
Feb 28, 2007 (7:12 am)
-
|
|
Replying to: steve_ (Apr 12, 2007 2:07 pm)
I have a 2002 xlt 4x4 and had the intermittant flashing light issue. Took it to a trusted mechanic and he diagnosed a 4x4 control module. Said could have been actuator motor which would have been more expensive. Charged me $360.00 p&l. I also had a dealer check and they said the same thing, although they would have charged me $480.00. Got it done just in time for the snow in Chicago.
Dave
|
- #22 of 88
-
Re: 4x4 problem [news1]
by jko29
-
May 02, 2007 (8:06 am)
-
|
|
Replying to: news1 (Feb 27, 2007 9:18 pm)
Hello
I had the exact same thing happen. Battery died, got it jumped then 4x4 lights started the blinking every 5-10 min and it wont engage 4 wheel drive.
Did you ever get an answer? I am still having the problem.
|
- #23 of 88
-
How to disengage front hubs?
by gnrosefan
-
May 28, 2007 (5:38 pm)
-
|
|
Replying to: steve_ (Apr 12, 2007 2:07 pm)
I have a 1998 ford explorer 4.0 4wheel high/low blinking and universal/cvjoint (not sure which) is banging and told that my 2 front hubs are engaged and need to be disengaged i was wondering if there is a way to manualy disengage them with out pulling them out of the car even if it means i only have 2 wheel drive. I apprecaite your time and opinions thanks
|
- #24 of 88
-
Re: 2002 4x4 EB Explorer [rocky32]
by jsims
-
Jul 08, 2007 (3:57 pm)
-
|
|
Replying to: rocky32 (Feb 25, 2007 10:14 am)
I have the same problem! Have you been able to find out what the problem is?
Jonah Sims
please send me an email if you have an answer
jonahsims yahoo.com
|
- #26 of 88
-
...
by chris89883
-
Jul 13, 2007 (2:23 pm)
-
|
|
Replying to: steve_ (Apr 12, 2007 2:07 pm)
sounds like a bad axle, look under your truck and see if one of your front axles is loose. if their good then i suggest you take your truck to any shop with diagnostic scanner and they will tell you whats wrong with it.
|
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
SUVs 
