Sign In Join

Dodge Dakota Climate Control

121 messages,  Last post on Sep 03, 2008 at 3:07 PM

You are in the Dodge Dakota Forum. Your Host is kcram

What is this discussion about? Dodge Dakota, Truck


Messages Page 9 of 13
1
...
6
7
8
9
10
11
12
13
Prev
Next
Last
Go To Msg #
Search This Discussion

#74 of 121
Re: Dodge Dakota 2002 Overheating [bpeebles] by tommy63
Sep 18, 2007 (7:22 pm)
Reply

Replying to: bpeebles (Sep 18, 2007 6:57 pm)

It's a 4.7L. There is no coolant loss. I have belt on according to diagram under hood. One thing I have noticed is one side of radiator is hot (right side) while left is cool, that is while I'm standing facing truck. As for the thermostat, it's a 195 degree same as the one I took out, but did not buy it at Dodge Dealer. The spring on thermostat is in engine so to speak. Also my wife pulled our 24' Travel Trailer up here to Wyoming from La with the truck, but ever since then it has been overheating, so I made the changes but that did not help. Thanx
#75 of 121
Re: air conditiong controls not working properly?? [kschlichting] by xscout
Sep 19, 2007 (12:51 pm)
Reply

Replying to: kschlichting (Sep 17, 2007 7:09 pm)

Sounds like a vacuum problem. Do you notice the air also going to the floor even when set on dash when you go from a steady speed to accelerating? If so it could be a broken vacuum line under the hood or the vacuum motor that moves the door for the dash air.
#76 of 121
Re: Dodge Dakota 2002 Overheating [tommy63] by bpeebles
Sep 20, 2007 (6:39 pm)
Reply

Replying to: tommy63 (Sep 18, 2007 7:22 pm)

The fact that you noted that one side of the radiator is signigicantly cooler than the other side points to a problmem with lack of coolant FLOW.
 
Do not forget that the 4.7L semi-hemi uses a BYPASS cooling system. This is noted by the fact that the thermostat is mounted LOW on the engine (not at the top of it) This type of cooling system ALWAYS flows coolant thru the engine past the thermostat. One end of the thermostat 'senses' the temparture of this engine flow and the other end of it 'throttles' the flow of coolant out of the radiator and precesicely mixes it into the hot engine coolant. This is why using a 'normal' thermostat will really mess up the cooling system because it does not have the ability to perform this function.
 
Here are a couple of other things to think about;
Does the heater put out heat?
Did you "burp" the air out of the cooling system using the special valve at the high point of the cooling system? (above power-steering resivour on radiator plumbing)
 
BTW (for future reference): It is worldwide standard to speak of "right" and "left" side of a vehicle based on the point of view from sitting in the drivers seat. (not standing in front of it facing it)
 
For example: The right headlight is the one on the PASSENGERS side.
#77 of 121
Re: Dodge Dakota 2002 Overheating [bpeebles] by tommy63
Sep 20, 2007 (9:10 pm)
Reply

Replying to: bpeebles (Sep 20, 2007 6:39 pm)

Mr., Peebles
I wanted to let you know that through your advice my truck is now back on the road. I did the burp thing as you advised, put an identical thermostat in truck to the one I took out, and all is well with my Dakota. Sir, I appreciate all the advice/help you gave in getting my truck fixed. THANK YOU SO VERY MUCH. I do have one more question. Why is the 4.7L called a semi hemi?
#78 of 121
Why is the 4.7L called a semi hemi? [tommy63] by bpeebles
Sep 21, 2007 (6:06 pm)
Reply

Replying to: tommy63 (Sep 20, 2007 9:10 pm)

That is an easy to answer question...
 
First of all, lets review why an engine would be called a "Hemi" in the first place. The term "Hemi" is slang for "Hemisperical". In a piston engine, the area from the top of the piston to the top of the cylinder head by the valve heads is known as the combustion chamber (this is actually just an area of air!). The combustion chamber on most overhead valved AUTOMOTIVE engines are either wedge shaped (think of a piece of pie) or hemispherical (think of tennis ball cut in half). The cylinder head design dictates the combustion area shape, so when someone says "hemi", it really only refers to the engine's cylinder head having a hemispherically shaped combustion chamber.
 
Hemi heads have the spark plug located at dead center of the combustion chamber, which makes for an extremely efficient & powerful fuel/air mixing & flame burn (actual igniting of the fuel/air). Hemi heads also have ideal valve placement to help the flow of air (intake & exhaust) through the cylinder head. In simple terms, the head design is VERY efficient, and allows an engine to make excellent power! On the downside, hemi heads themselves usually are quite heavy & large, and valvetrains can be somewhat complex (read: expensive).
 
The 4.7L engine is a "semi Hemi" because the head is almost a perfect sphere... except for a small bump.
 
Here are some links which further describe the 4.7L semi-hemi
http://www.allpar.com/mopar/47.html
http://www.thehemi.com/news.php?id=20020826-1
#79 of 121
Re: Why is the 4.7L called a semi hemi? [bpeebles] by tommy63
Sep 22, 2007 (9:23 pm)
Reply

Replying to: bpeebles (Sep 21, 2007 6:06 pm)

Mr., Peebles
Thanx for the explanation on the engine. My wife said to tell you Thanx very much for the help in getting our truck fixed. Again, Thank You.
#80 of 121
Re: Why is the 4.7L called a semi hemi? [tommy63] by dustyk
Sep 24, 2007 (3:51 pm)
Reply

Replying to: tommy63 (Sep 22, 2007 9:23 pm)

As an aside to Bpeebles excellent explanation, when Chrysler first developed the "semi-hemi" combustion chamber in the 1950s, they were referred to as polyspherical engines, meaning they used a combination of wedge and hemispherical designs.
 
Regards,
Dusty
#81 of 121
blower motor switch by magnummark
Dec 07, 2007 (8:33 pm)
Reply
Hello all
94 dakota 318 w/air 2wd
short story... blower motor worked only on high. then it didn't work at all. the way it happened i'm pretty sure it is the speed control. checked resistance on it but without documentation for the terminals....
help me please!!!!
#82 of 121
Re: blower motor switch [magnummark] by rolandtignor
Dec 08, 2007 (6:29 pm)
Reply

Replying to: magnummark (Dec 07, 2007 8:33 pm)

It's your fuse relays. My blower wouldn't even work. Mine was on the outside firewall in the engine compartment on the passenger side.
I hope that helps.
Thanks
#83 of 121
Re: blower motor switch [magnummark] by bpeebles
Dec 08, 2007 (8:55 pm)
Reply

Replying to: magnummark (Dec 07, 2007 8:33 pm)

Check the Blower resistor - that is the most common failure for blower motor issues. It is the resistor which determines all the fanspeeds.

Messages Page 9 of 13
1
...
6
7
8
9
10
11
12
13
Prev
Next
Last
Go To Msg #
Search This Discussion
To POST a message, please Sign In.

New? Join Now!

Forum Tools

Please sign in.
Email Address:

Password:

Forgot Password?

Search Forums

Enter Keyword(s)

Advanced Search

Browse by Vehicle



View All Vehicles
Advertisement
Ask the Community
See What People Are Asking

Browse by Board

Browse by Topic


View All Topics
Advertisement