Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
Pickups Dodge Dakota Dodge Dakota Climate Control
195 messages, Last post on Sep 16, 2009 at 11:56 AM
You are in the Dodge Dakota Forum. Your Host is kcram
|
Replying to: simonds (Dec 08, 2008 8:28 pm) Don't have any suggestions regarding the lights, however one thing that is common to both is the Central Timer Module. Best regards, Dusty |
|
2001 dodge dakota put in new heater blower and resistor card so now when i use remote starter it works just fine but once i put in gear i have no heat
|
|
I live in Saskatchewan at present it is -40, The heater on my 2003 Dodge Dakata QUIT working which is expected in this cold weather, I took it apart and checked all fuses, there all working, I then pulled the plastic shroud off, and unplugged the wiringplugin to the main blower switch, and test lighted it and found there is no power at the main wire or anywhere in the blower plugin switch. Is there any other places to confirm power source, .................Lorne
|
|
|
Replying to: taropat (Dec 20, 2008 4:06 am) Regards, Dusty |
|
|
Replying to: LorneQue (Dec 20, 2008 10:51 am) With respect to vehicle ground (frame & body), which is negative, power is delivered to the Heater Blower Motor at pin 1. DC power gets to the A/C-Heater Control Switches via the Blower Motor Resistor at pin 2. The circuit is as follows: 1. Fuse #13 (40 ampere) in the Power Distribution Center (PDC) located under the hood next to the battery GOES TO 2. Ignition Switch pin 1, then comes out pin 2 (run position) GOES TO 3. Heater Blower Motor pin 1. DC power goes through the motor at pin 2. GOES TO 4. Blower Motor Resistor Block at pin 2 (DC in). The resistor is located next to the Heater Blower Motor. The black blower motor wires will go to it. DC power goes through the three (3) resistors (pins 3, 4, & 5), plus passes through without resistance at pin 1 of the resistor block. GOES TO 5. The A/C-Heater Control Switch Pin 1 resistor block - to - pin 10 of the heater control switch (high position) Pin 3 resistor block - to - pin 3 of the heater control switch (not so high position) Pin 4 resistor block - to - pin 7 heater control switch (medium position) Pin 5 resistor block - to - pin 2 heater control switch (low position) Pin 8 of the Heater Control Switch is 12 VDC for the panel illumination lamps. Pin 5 of the Heater Control Switch goes to ground. The most common cause of blower failure on Dakotas of your vintage is the resistor block, a very common problem. I would recommend removing the resistor block, which is mounted to AC/Heater box next to the blower by two screws. I suspect you will observe signs of pins and wires overheating at the connector. This will need to be repaired. The resistor is part number 5174618-AA and a connector repair kit is (was) 5017124-AA. If the resistor displays signs of overheating, you'll probably need both. Stay warm up there in Alaska! Best regards, Dusty |
|
|
Replying to: dustyk (Dec 20, 2008 11:34 am) |
|
|
Replying to: LorneQue (Dec 20, 2008 11:55 am) I don't know why I thought you were in Alaska, but good luck. Regards, dusty |
|
|
Replying to: LorneQue (Dec 20, 2008 11:55 am)
|
|
|
|
|
Replying to: teneubec (Jul 02, 2007 4:31 am) |
|
You are here:
Forums
Pickups Dodge Dakota Dodge Dakota Climate Control
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2010 Dodge Dakota
Browse by Board
Browse by Topic
Today's Chats
