Edmunds.com | Inside Line | Auto Observer Your Account | Help | Directory
You are here:
![[F]](http://a332.g.akamai.net/f/332/936/12h/www.edmunds.com/media/townhall/webxicons/site.gif){kind=small}
Forums
SUVs Chevrolet Suburban & Tahoe Suburban Tahoe Seat Questions
339 messages, Last post on Dec 04, 2009 at 1:30 PM
You are in the Chevrolet Suburban & Tahoe Forum. Your Hosts are steve_ & tidester
|
Replying to: jessegonzales (Nov 25, 2008 3:56 pm) |
|
|
Replying to: wwwToddH (Nov 25, 2008 1:36 pm) This is to update and correct my earlier post(s). We have been looking into swapping or buying locally. According to a knowledgeable man my husband spoke with today (the guy deals in these type of seat swaps) -- it is NOT possible to swap captains chairs for bench seat without drilling holes in the floor. The bolt patterns are different. Sounds like it won't work even within the same model year, not unless you don't mind a few extra holes in your floor. |
|
|
Replying to: bradb1 (Nov 26, 2008 9:03 pm) Tahoe-to-Suburban seat swap does not work. Mounting in floor is totally different. I would believe that swap between two Tahoes would work though. I have a light tan bench seat in very good condition. I am in Baton Rouge, LA. How far is Pensacola for you to drive to? It is about 5 hours for me. Arrie |
|
|
Replying to: steve_ (Oct 10, 2008 3:36 pm) Any help would be great. Thanks
|
|
|
Replying to: jdicken1 (Dec 17, 2008 8:07 pm) Seats Front Seat Adjuster Motor Removal & Installation To Remove: NOTE: The seat adjuster motors can not be replaced separately. If a motor is defective, the seat adjuster will have to be replaced as an assembly. Remove the front seat. Remove the seat side trim panel. Remove the seat cushion frame from the seat adjuster. Remove the inboard mounting nut and remove the seat belt buckle from the seat track. Disconnect the seat belt electrical connector Remove the seat back frame from the seat adjuster. Remove the seat back hinge/recliner mechanism. Remove the seat adjuster track cover. If equipped, remove the memory module, Remove the seat adjuster from the vehicle. Disconnect and replace the motors as needed. To Install: Position the memory module to the seat. Install the mounting screws. Tighten to 26 lb in (3 Nm). Position the inboard seat belt buckle to the seat track. Install the mounting nut. Tighten to 39 ft lb (53 Nm). Connect the seat belt buckle electrical connector. Install the seat adjuster track cover. Install the seat back hinge/recliner assembly. Install the seat back frame to the seat adjuster. Install the seat cushion frame to the seat adjuster. Install the seat side trim panel. Install the seat. Calibrate the seat if equipped with memory seats. Now, I'm not a mechanic, but if you could somehow get in there, maybe you could figure out how to replace just one of the motors. That's assuming it's really a motor that's the issue and not a broken wire or circuit board trace or the module or one of the switches. There's also a 30A seat circuit breaker, but I don't think you'd have any of the functions if that was blown.
|
|
|
Replying to: steve_ (Dec 17, 2008 9:15 pm) |
|
|
Replying to: bradb1 (Nov 26, 2008 9:03 pm) |
|
|
|
|
Replying to: lolimax (Nov 23, 2008 6:34 pm) Are you still interested in doing the swap? |
|
|
Replying to: bradb1 (Nov 26, 2008 9:03 pm) |
|
|
Replying to: binghamm (Jan 10, 2009 8:52 pm)
|
|
You are here:
Forums
SUVs Chevrolet Suburban & Tahoe Suburban Tahoe Seat Questions
New? Join Now!
Forum Tools
Search Forums
Browse by Vehicle
2010 Chevrolet Tahoe
2000 Chevrolet Tahoe Limited/Z71
Browse by Board
Browse by Topic
Today's Chats
